Liczymy pasujące modele…
The housing consists of two parts. The cap is snap-in. The HDMI and USB-C ports are easily accessible and not recessed into the housing. The housing has a cutout that allows access to the microSD card without disassembly and holes for…
2parts, held together by four M3 10mm screws and nuts. no supports needed. OpenSCAD source available. New : Optional top that houses 4x4x4mm NdFeB magnets. Even half-populated it will stick to any metal case (just be aware of magnetic…
This is a custom-designed protective case for the Sipeed NanoKVM Lite, an open-source KVM switch that allows you to control multiple computers with a single keyboard and mouse. The case is designed to provide both protection and…
This case is a refined version of the original Sipeed NanoCluster Case, redesigned to support the Noctua NF-A6x25 (5V PWM) fan and to provide a more convenient opening/closing mechanism. I’ve also added a bottom access hole so you can…
Some versions of the NanoKVM come with a non-standard PCIe bracket that is too high for the mount hole. This model is based on my measurements but has the correct height. It's somewhat flexible but does not compromise the structure when…
Case for Tang Primer 25K FPGA board that exposes all buttons/LEDs/connectors, with optional case for SDRAM expansion board. It uses 4x M2.5x12 screws and 4x M2.5 nuts to attach the two halves (the SDRAM case snaps together/doesn't need…
This is a simple 3D-printable mounting bracket for a Sipeed NanoKVM , designed to mount the device on the side of a rack homelab setup. It's universal, so you can print for either left/right mount, buttons and OLED display are accessible.…
Enclosure for the SBC Sipeed Longan Pi 3H Hardware needed: 4x M2.5 x 5 or 7mm
Enclosure and stand for SiPEED Tang Nano 20k FPGA to use as a console or just to keep dust off. There is a kit out which has the SiPEED Tang Nano 20k FPGA packaged with some controller port boards and a couple of no-name repro DS2…
A simple protective case for the Sipeed LicheeRV Nano Wireless board. Snap-fit design - No screws or glue needed, just snap it together. Micro SD card slot - card stays accessible for reflashing without opening the case. STEP file…
Sipeed NanoCluster DeskPi Rackmate 10 inch Rack Mount 2U
Split to objects in slicer. You can make the feet using hot glue.
buttons adjusted for less tight fit, original design did not work on my printer. including the openscad file uses so anybody can adjust for their printer.
Sipeed NanoCluster DeskPi Rackmate 10 inch Rack Mount 2U
This is a simple 3D-printable mounting bracket for a Sipeed NanoKVM , designed to mount the device on the side of a rack homelab setup. It's universal, so you can print for either left/right mount, buttons and OLED display are accessible.…
Case for SiPEED Tang nano 9k board. Print: 0.4 nozzle, 0.2 layer, 15%infill, 3 wall, 4 top, 4 bottom, no support needed (if no problems with bridges). Assembly: add a piece of foam rubber under the screen 4pcs self tapping screws m2.3x8,…
There are other NanoKVM cases but I wanted one that would print without supports for an easy and good looking case. This model was designed with the heat sink in mind, but it is optional. To install it is very simple: place the NanoKVM…
Case for the Sipeed MAix BiT . Part 1 does not need Supports, Part 2 does. Print Settings Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: doesn't matter Category: Electronics
Split to objects in slicer. You can make the feet using hot glue.
The MAiX Go kit from SiPEED is a platform for experimenting with RISC-V, MicroPython, neural networks and face recognition. It comes with some mounting hardware, but I didn't like it, and besides, the front bezel is fragile and mine…
buttons adjusted for less tight fit, original design did not work on my printer. including the openscad file uses so anybody can adjust for their printer.
Simple frame to hold the parts together. Fits Maixduino and Maix Bit boards. The TFT display is held in place by a click-in frame. There are two frame versions with slightly different cutouts. You may have to widen the FPC cable cutout by…
Ultra-compact and fully printable snap-lock case for the Sipeed M1/M1w Dan Dock dev board (MAIX RISC-V 64 / Kendryte K210 board). It makes it look like a minimalist point&shoot camera, case is only 18 grams (0.7 oz) and assembled…
This is a case for the Sipeed Longan Nano RISC-V devboard, with holes for the USB C receptacle and JTAG header and buttons for Boot and Reset, a small opening in the top part allows the LED to remain visible. I removed the display. Print…
