Liczymy pasujące modele…
This is a Solar Radiation Shield aka. Stevenson Screen for Air Temperature and Humidity Measurement. It's inspired by micromet's shield but I redesigned it from scratch. It should be compatible with sensor mounting adapters for their…
This is a box for meteorological instruments (such as a thermometer or a hygrometer) that protects them from sunlight, water, snow, and strong winds. This box is based on a prior design I made and uploaded here . After days of frustration…
The basket prints as a single piece, rather than individual interconnecting pieces, so it's less likely to come apart in inclement weather - or if a dog runs into the pole. The interior is designed for smaller sensors, up to 35mm x 58mm.…
Meshtastic Weather Station Node case compatible with the Acurite 06054 Stevensen Screen Node case with plenty of room for sensors Case snaps into screen securely but can be easily removed All connectors come out the bottom of the screen…
Steven Universe is an American animated television series created by Rebecca Sugar for Cartoon Network . It tells the coming-of-age story of a young boy, Steven Universe ( Zach Callison ), who lives with the Crystal Gems—magical,…
This is a 3d print design to build your TPU. This is the STEAP version of it. Work in progress! I made an ESP32 WROOM version to control the 3 frequencies. To configure the TPU settings from the ESP32: Upload the firmware using ARDUINO…
Radiation shield for temperatures and humidity sensor Tuya Zigbee
Added a mount bracket with camera clamp adapter. stevenson_large_mount_glue – smaller ring and smaller holes. Use 1.75 mm filament and some acetone or super glue to bond the parts together. stevenson_large_mount_screw – larger ring and…
Purpose designed part, may not fit your rifle exactly as the Stevens marksman rifles were built in the 1930's and the wood stocks may not all be the same. i.e. mounting hole locations, profile, curvature, etc. Original crumbled and was…
Added a mount bracket with camera clamp adapter. stevenson_large_mount_glue – smaller ring and smaller holes. Use 1.75 mm filament and some acetone or super glue to bond the parts together. stevenson_large_mount_screw – larger ring and…
This is an alternative to the trigger guard and floorplate for Boyds AT-One type stocks. It is designed to fit an AT-One Steven 300. It is intended to replace the 93E MKII. Installation is very simple; you will only need three screws in…
Intro A compact, modular Stevenson screen designed specifically for the Aqara WSDCGQ11LM square temperature & humidity sensor. The sensor installs into the Lower Part using a snap-in cradle with a latch (no screws or glue) and can be…
Steve (Steven Paul) Jobs — Buste (avec ou sans lunettes) 🇫🇷 Description Ce buste représente Steven Paul Jobs dans une interprétation sculpturale classique, limitée à la tête et au haut du torse, reposant sur un socle discret. Les volumes…
If you are lazy to source the threaded shafts, this just clicks in. Tested with PETG, the pins are still relatively small, and the layer aligment is not greatest, so better dont try to disassamble it too many times... Just screw it on to…
Steven Universe is an American animated television series created by Rebecca Sugar for Cartoon Network . It tells the coming-of-age story of a young boy, Steven Universe ( Zach Callison ), who lives with the Crystal Gems—magical,…
Meshtastic Weather Station Node case compatible with the Acurite 06054 Stevensen Screen Node case with plenty of room for sensors Case snaps into screen securely but can be easily removed All connectors come out the bottom of the screen…
This screen can contain additional sensors, not only described in sensor community manual (GPS, OLED/LED display etc). PCB board Also you can use compact and convenient PCB board for connecting components used in the Sensor Community…
Stenvensonův radiační štít vhodný pro čidlo meteostanice. Vnitřní průměr 81mm výška 78mm. Tisknutelné bez podpor. Vytvořeno pro čidlo Thermopro TX-7C.
Stevenson screen for the temperature sensor of my weather station (BME280 and an additional Thermistor, but works of course also with DHT11/DHT22 or similar sensors). I printed it with white PLA and have no problems after about 12 months,…
GoPro Stem Mount for Stevens/Scorpo hexagon shaped stems. Simply use zip ties (5mm) to fix it to the stem.
Purpose designed part, may not fit your rifle exactly as the Stevens marksman rifles were built in the 1930's and the wood stocks may not all be the same. i.e. mounting hole locations, profile, curvature, etc. Original crumbled and was…
Bonjour, Un ami à cassé ce petit clips de garde-boue de son vélo de marque STEVENS, le modèle est un "randonneur lite" de 2016. J'ai donc reproduit la pièces qui est maintenant disponible pour tout les cyclitse qui auraient rencontré le…
Remix of @Tom_62253 excellent Stevenson Screen. I needed to mount on a vertical pole that have a 50mm diameter. by this i also needed to change the screw hole so it was in the rights place for the vertical pole. All other parts for this…
Even Steven card from Balatro Mario energy All credit to LocalThunk and Balatro for the design
Needed a twofer stevenson screen for my ecowitt WN32 and WH57 modules but didn't want to overengineer the thing soooo The two modules slide into the stevenson screen, but they're actually held up by the bottom screen piece. This helps…
To build the Stevenson screen, you need : Stevenson screen : 1x bottom Nx cup to reach the desired height (7 for me) 1x top1 1x top2 Base : 1x base 1x PcbHolder and PcbCover 1x ExtensionArm, SolarCellHolder 1x SmaHolder (if you use an…
Outdoor temperature sensor cover - Stevenson screen. For sensor with 7mm diameter. In sensor tube mount added cutouts for zip ties. Printing without support. For assembling 2x M4x20 are needed. In cover two holes needs to be taper M4…
🌌 THE OVERVIEW I incline myself to space There was no ghost on the moor No open window No monkey's paw I love Steven Wilson's music, and so I created a set of 3D printable abstractions to represent his discography. This can be used as a…
We used this stencil to spray paint “Failure Management” onto an old red long sleeve shirt in white. It works out great and lasts forever with base color paints with no glitter or any other additives that get pulled off in the wash. Very…
Support for stevenson monitor. Mast mount with straps. M4 screw for monitor. Designed for round mast mount of https://www.printables.com/model/202225-solar-radiation-shield-stevenson-screen-for-outdoo
This is a remote part of my weather station, meant for measuring temperature/humidity/pressure and sending it via ESP-NOW to the main unit - ESP32S3/Lilygo T5 4.7 E-paper display . For anybody interested source code can be found here:…
Original by FabReyes on Thingiverse Printer Settings Quality: Resolution: 0.20mm Ironing: All Top Surfaces – Optional but very nice results Wall Generator: Arachne Strength: Perimeters: 3 Infill: 12% Speed: First Layer: 25 mm/s First…
Original by FabReyes on Thingiverse Printer Settings Quality: Resolution: 0.20mm Ironing: All Top Surfaces – Optional but very nice results Wall Generator: Arachne Strength: Perimeters: 3 Infill: 12% Speed: First Layer: 25 mm/s First…
Original by FabReyes on Thingiverse Printer Settings Quality: Resolution: 0.20mm Ironing: All Top Surfaces – Optional but very nice results Wall Generator: Arachne Strength: Perimeters: 3 Infill: 12% Speed: First Layer: 25 mm/s First…
Original by FabReyes on Thingiverse Printer Settings Quality: Resolution: 0.20mm Ironing: All Top Surfaces – Optional but very nice results Wall Generator: Arachne Strength: Perimeters: 3 Infill: 12% Speed: First Layer: 25 mm/s First…
I really like the SwitchBot outdoor temperature and humidity sensor as it is, but I don’t have any shaded area to place mine. As a result, direct sunlight affects the readings and makes it unreliable. To solve this, I designed a simple…
simple slot everything together and secure with the the M3x60 bolts. Parts to print: Top x1 Intermediate screen x2 base x1 mounting bracket x1 Print Settings: Filament - PETG (or other UV resistant filament) Layer height - 0.3 Support -…
Inside dimensions: 44x44x20mm Sonoff SNZB-02 temperature and humidity dimensions: 42x42x16mm Category: Outdoor & Garden
Outdoor thermometer SwitchBot Indoor/Outdoor Thermo-Hygrometer sensor, stevenson screen
• Compatible with camera adapters • M12 × 1.5 mm thread for PG7 cable glands • Dedicated thread for the Stevenson screen See my other posted models for mounting arms and 26.4 mm (3/4") pipe clamps. Due to several requests, I added a…
Primeros pasos con Fusion 360 creando un protector para un termómetro de la marca TFA. El diseño es fácilmente adaptable a otros modelos, ya que permite añadir o quitar láminas intermedias según se necesite. El conjunto está formado por…
Learn more about Braillest's embossing and repair process here . https://github.com/Braillest-Books/The-Strange-Case-of-Dr-Jekyll-and-Mr-Hyde-by-Robert-Louis-Stevenson
Рассчитана для использования с ESP или Zigbee модулями. 4 слота для батареек AA. Прокладка печатается FLEXом. Print Settings Printer: Prusa like Rafts: No Supports: Yes Filament: Bestfilament ASA, ABS white Notes: Заполнение по вкусу.…
This is an alternative to the trigger guard and floorplate for Boyds AT-One type stocks. It is designed to fit an AT-One Steven 300. It is intended to replace the 93E MKII. Installation is very simple; you will only need three screws in…
Intro A compact, modular Stevenson screen designed specifically for the Aqara WSDCGQ11LM square temperature & humidity sensor. The sensor installs into the Lower Part using a snap-in cradle with a latch (no screws or glue) and can be…
Steve (Steven Paul) Jobs — Buste (avec ou sans lunettes) 🇫🇷 Description Ce buste représente Steven Paul Jobs dans une interprétation sculpturale classique, limitée à la tête et au haut du torse, reposant sur un socle discret. Les volumes…
Love this series! It is setup for multi-colour printing, but you could do it with a single extruder and just change from black to white. Print larger, rather than smaller as details are quite small. If you are using the .stl file remember…
If you are lazy to source the threaded shafts, this just clicks in. Tested with PETG, the pins are still relatively small, and the layer aligment is not greatest, so better dont try to disassamble it too many times... Just screw it on to…
Using https://map2model.com/ I created a map of Lake Stevens followign the city limits and generated a 3mf for multicolor printing. This was designed to print on a Prusa XL.
Bewitched - Samantha Stevens - 1964 3D printable model.
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm The Model is 133.4x133.4mm in size You may print at higher layer heights below the Base Thickness of 0.48mm The Max allowed Thickness is 2.24mm and the Actual…
Modified the original model to have bigger wall mount and to have less parts. Consists of two parts only - the mount and the cover that slides into the mount. Just place the mount, put the sensor inside and slide the cover. The cover does…
Grey's Anatomy - Izzie Stevens (Katherine Heigl) - 2005 3D printable model.
Grey's Anatomy - Izzie Stevens (Katherine Heigl) - 2005 3D printable model.
Air360 Stevenson Screen Enclosure is an outdoor housing for the air360 air quality monitoring station. The enclosure is designed to place the air360 ESP32-S3 shield, the controller board and connected sensors inside a ventilated…
A modular, customizable, snap together general purpose weather protector (aka Stevenson screen ) for sensors like my temperature and humidity sensor. Usage : Open the .scad file and enter the bounding box of your sensor (or thing) you…
CR2032 batteries don't really "live well" in freezing conditions, so i converted one Xiaomi sensor to run on two AAA batteries. I added a battery holder on the stevenson screen from "Mepea". I uploaded only center part with battery…
Rock Bands - Aerosmith - Steven Tyler 3D printable model.
Stevenson Screen can be hung anywhere with eye bolt. Nozzle: .4 mm Layer: .2 mm Filament: Sunlu Rapid PETG White PEI Build Plate Magigoo Adhesive Temperature: 250 No Supports 15% infill 3 Walls 1 1/2 Inch Eye Bolt ¼ Inch (hardware) and…
Stevenson-screen style solar radiation shield for the IKEA TIMMERFLOTTE outdoor thermometer sensor (64mm x 18mm). Printable as one piece, no assembly needed. Features: - 5 angled louver plates (45 deg slope) for airflow + sun shading - 12…
Ventilated, support-free enclosure for a DIY weather station living inside a Stevenson screen. The ESP32-C3 Super Mini and the LM393 rain-sensor controller sit side by side in the main box; the AHT20 and BMP280 live in two separate…
U can use this screen for temp and humidity sensors for oudoor projects.
Luftdata? I'm part of a Swedish Citizen science projekt luftdata.se measuring air particles using a sds011 sensor. It's a branch from the original german projekt luftdaten.info where you can read build instructions etc in English. (You…
I wanted a holder for my ESP8266 dev board and some sensors within my stevenson screen so I made a simple mesh holder with plenty of room! Print Settings Printer: RepRapPro Mendel Rafts: No Supports: Doesn't Matter Resolution: 0,2 Infill:…
A simple set of models to make a stevenson screen. These slide over a 6mm Dalas based temperature probe cheaply found on ebay. For more information about Floaty McFloatface, from which this thing is from, visit…
Summary Simple stevenson screen for outdoor thermometers. Stackable, and easy to print. OpenSCAD file is included if you want to customize it further. I used this to mount my AcuRite outdoor temperature sensor. Design Each level has holes…
I purchased a bunch of Xiaomi LYWSD03MMC temperature and humidity sensors for use around the house. They are cheap and work very well. I re-flashed mine with some open firmware and have been using them very successfully with Home…
This is a solar radiation shield for mounting a temperature sensor outdoors. The shield allows air to flow through freely, but protects the thermometer from direct and reflected solar radiation. This provides a much more accurate…
A stevenson screen, i made it for my own weather station based on an ESP01 (ESP8266) and a BMS280. I self printed it in white PET-G. It is also possible in PLA but then you have the problem that it will dissolve over time. In my picture i…
These models are designed to make fitting the component parts needed to run the Enviro Weather (Pico W Aboard) & Enviro Urban (Pico W Aboard) boards into the Stevenson Screen from Pimoroni easier. The 'LiPo Amigo Pro holder.stl' part is…
This is a Stevenson Screen meteorological shelter for enclosing an outdoor weather station. It's been designed to fit on to 40mm push fit waste pipe (which is very cheap and easy to get). It's a very tight fit to ensure it doesn't come…
This is a printable replacement stock for the Stevens Crackshot 26. it is strongest printed along the long flat base. The fusion 360 file is included so you can adjust the depth of the larger hole to adjust for different sized screws.…
A fun and educational toy. Just simply print as many of each cog as you want (I suggest printing a larger number of the smaller cogs) plus some connecting rods, and frame. The kit is designed to take a small cd-rom motor, but this is…
I have printed the parts using PETG filament as this was the only filament in blank white color I had in stock. Unfortunately the filament has a very poor quality. The filament appears to have very poor diameter accuracy. For this reason…
Another Stevenson screen in cylindric shape. No internal support to hold the sensor. Preferred filament color is white to reflect most sun radiation. Preferred filament is PETG, but other filament may be used. No support, no brim…
You can find the V2 of this project here : https://www.printables.com/model/1173424-stevenson-screen-v2-for-temperature-sensor You need: one base one bottom one top how many middles you need to reach the desired height 4 threaded shaft…
This Stevenson screen is compact, fully printable and easy to mount. The socket has a hole with a 12x1,5 inside thread to hold a standard PG7 cable gland. To the top, the socket has an 20x2,5 outside thread to hold the hat. The hat must…
Public domain island ukulele model by TheDuckCow . Originally uploaded to Blend Swap . This model can be printed, but the body is hollow, so it presents a serious overhang challenge.
I created this Stevenson Screen for our outdoor thermometer. There's plenty of similar designs on thingiverse, but I'm also learning how to create such things with Fusion 360, so it was a learning experience as well. There are two parts…
He’s a frozen treat with an all new taste Cause he came to this planet from outer space! A refugee of an interstellar war But now he’s at your local grocery store! It's COOKIE CAT! Also it's a box. I have a couple short videos showing how…
I realise that there are many spool holders on Thingiverse already, but I wanted to design my own. A very basic and simple design, printed in two parts. No supports needed. Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator…
I remix model foe wall mount. No need supports.
I lost some files between building this and now, and did not make a parts list when building. I have the key files included and can try to find specific missing models if requested. I posted this as there was enough work that went into…
This cage helps to mount your Dragino LHT65 temperature and humidity sensor in an Stevenson Screen https://www.thingiverse.com/thing:83969
Round gem with pentagon top facet. The side-facets aren't super-sharp, but trying to blend from a pentagon to a circle gives you that. This file is scaled in inches, with a roughly 2" final diameter on the gem. This file is a shelled…
Solar Panel Holder + Stevenson Screen from those things i build myself a… Solar Powered, Weather Station! featuring LoRa technology this is a standalone weather station i build. the main point i wanted to achieve is to broadcast the data…
designed to fit into a 20mm diameter electrician's RK tube. print enough "bodies" to contain your sensors. with 2 body+cap i inserted a DHT11 for humidity and temperature, and a BH1750 for brightness. diameter 60mm
The is a Stevenson Screen that I designed for my Arduino based weather station. The top is designed to install M3 brass threaded inserts. On mine I printed 2 middle sections and a top and bottom to make my screen. I used M3x65mm screws to…
Version 2 is available now! Outdoor Weather Station based on ESP32 and BME 280 Little outdoor weather station with ESP32 (NodeMCU and similars) box which can be mounted to a rail or similar (clamp diameter 22mm). It has an arm to hold the…
the sensor is from aliexpress: (20x25x71 mm) https://de.aliexpress.com/item/1005006008193742.html the two parts just snap together I would only print this in white :) Other colors including black will heat up more in the sun! printed with…
Hi weather frogs, today I finally finished the housing for the AQM II, extruded it using a 3D printer with UV-resistant ASA filament. Since I still had a Stevenson screen, I looked for a variant to integrate the AQM II. Since I really…
Wanted the screws to be recessed just to make it look a little nicer
Building on the Stevenson screen as linked below, this simply adds a bit of a hook or loop to attached the sensors.
I remixed the model in order to hang it in a tree and made the holder more stable. Need no supports.
Replica of Rose Quartz's sword from the animated show Steven Universe. The sword blade is reinforced with a threaded steel rod during assembly. Photos show the sword after gluing, sanding, and painting. We have a video covering the entire…
INSURGENTES ↑ A bottle not for sharing Poison for the fairies I love Steven Wilson's music, and so I created a set of 3D printable abstractions to represent his discography. This can be used as a beverage coaster , or just for display .…
Grace for Drowning I'm a collector, I collect anything I find I love Steven Wilson's music, and so I created a set of 3D printable abstractions to represent his discography. This can be used as a beverage coaster , or just for display .…
The Raven That Refused To Sing (And Other Stories) Sing to me, Lily, I miss you so much I love Steven Wilson's music, and so I created a set of 3D printable abstractions to represent his discography. This can be used as a beverage coaster…
![Steven Universe Ukulele [Rigged]](https://media.printables.com/media/prints/447403/images/3688778_c74ffba2-3f11-43d0-a9d6-84e0a4b8f43a/41a31ca62b1a831a61ae60ff06fe6a52.jpg)
