Liczymy pasujące modele…
Scheppach Akku Halterung (MGT410) für das ordentliche Aufhängen von Akkus der Fima Scheppach sollte auch für Akkumodel: BA2.0-20ProS passen / Scheppach battery holder (MGT410) for neat hanging of batteries from the company Scheppach…
ATTENTION: the switch holder V1 is designed to be used with hobbywing 3652 motor or similar size!! (max lenght 53mm!!) otherwise use V2 or V3 instead. a simple mount for the hobbywing ezrun esc. the sct/mt410 2.0 chassis offers a place to…
Replaces original foam one that easily breaks on shock. Print in TPU.
Use M6 screw with washer and spring washer for the pin. Tight is just enough it can slide with expected amount of friction. Use 3x M4x10 (with washers). Replaces part #: P1058930-042
Carten T410 Rally steering cover, stops dirt and grass getting on the space by the steering
Carten T410 Rally Front skid to stop damage to the chassis
Use M6 screw with washer and spring washer for the pin. Tight is just enough it can slide with expected amount of friction. In case hanger is leaning under the label roll weight, you can use another M6 screw on the top, leave approx. 1 mm…
Carten T410 Rally Rear skid
designed some mudflaps for the Tekno SCT410 2.0 for an more scale look. you need: 6x m3x10mm screws 6x m3 nylock nuts 6x washer (optional) 2x mudflap mounts (preferred in petg or nylon) 2x mudflaps (preferred in tpu or cut a 2mm rubber…
Thanks to marsellus2k for the original design. The only change I made was to increase the length to fit different bodies. Category: R/C Vehicles
See diagram for assembly instructions. Needs 4, print laying on flat sides TKR7798 PRO607002 93245A115 94180A351
Carten RC T410 Rally, Servo move mod, moves the steering servo 1mm forward to allow Hobbywing Max 10 ESC
Print this in TPU with supports under, in the orientation in the file. You can adjust the number of perimeters and infill amount to adjust stiffness, but I used the slicer defaults.
THIS IS A CLEAN VERSION WITH NO WRITTING ON FLAPS. Printed in TPU 95 with 4 walls top and bottom 80% gyroid infill support on build plate only
Printed in ABS at 4 walls top and bottom, 40% cubic infill. Fits TIGHT on side guard, will need to short 2.4mm screws for install. Then use double back tape to secure your switch in place. WAY easier for a marshal to locate mid heat!
Added some bridges over the m3 nut holes to make it easier to print standing upright. Designed for .2mm layer height.
One of my nylock nuts came loose somehow and I lost the spacers that come with the rear hub package ( part number TKR6576 ) . This replaces them and they fit like a glove. You will need two of each direction, so either use the 3mf file or…
Print this in TPU with supports under, in the orientation in the file. You can adjust the number of perimeters and infill amount to adjust stiffness, but I used the slicer defaults.
Added some bridges over the m3 nut holes to make it easier to print standing upright. Designed for .2mm layer height.
Printed in TPU 95 with 4 walls top and bottom 80% gyroid infill support on build plate only
Printed in ABS at 4 walls top and bottom, 40% cubic infill. Fits TIGHT on side guard, will need to short 2.4mm screws for install. Then use double back tape to secure your switch in place. WAY easier for a marshal to locate mid heat!
THIS IS A CLEAN VERSION WITH NO WRITTING ON FLAPS. Printed in TPU 95 with 4 walls top and bottom 80% gyroid infill support on build plate only
ORGANIZZATORE GT410 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X3 PLUS / X4 PLUS
