Liczymy pasujące modele…
This mod will void your SSD's warranty but makes using them for recording much more convenient. Assembly requires two original screws and three additional M3x8 ones for the lid.
This is a tool less replacement adapter of the SSD caddy of the Atomos Ninja V. No screws or tools are needed in order to use your SSD with your Atomos. Also included is the clip (you have to print two of them) for the Smallrig 2209 cage…
I designed a sunhood for the Atomos Ninja V and Shinobi V. It is printed in two parts and then glued together. The main aspact is the screw to hold it in place.
Tomos APN 6 air cooler, fully printable NO supports All bridging must be no problem
I couldn't seem to find more of these that I could use with the Atomos connect on my Ninja V. I can confirm this works with the Ninja Ultra with a Connect module, the Shogun Connect and the Ninja V on a multi cam module as well. I used…
A sun hood for the Atomos Ninja V and Shinobi V that can be screwed into place. Supports are required and it's important that the model's position is upright with the edge of the screw contact point facing down.
simple print suport on the lead for the opening
Generally, there are two types of media that can be used with the Ninja V and other Atomos recorders using a similar caddy design - expensive AtomX drives that fit nicely in the slot and inexpensive caddies which accept a SATA SSD, but…
Atomos Ninja V / Shinobi 5" Screen cover
When the cover is attached, the threads and connectors on the side are still accessible.
Frame to attach the Small Rig Sun Shade to the Atomos Ninja V
Case for Atomos Ninja/Ninja Ultra based on Rugged Box by Whity. Fits following: Atomos Ninja/Ninja Ultra monitor-recorder NP-F battery (up to 7800 mAh) monitor mount SSD (with Master Caddy) cables etc. You will need 6× M3x30 screw (or 4×…
Specific box from @ Whity to fit an Atomos Shinobi 5" with its smallrig cage or not. I added extra space to add foam. Seal works fine if printed with TPU M3x30 screws :…
A slightly modified version of a simple sunhood for Atomos Ninja V to make it a bit shorter and more practical on the go. Obviously the effectiveness is reduced from the original model but if you angle the Ninja properly it can be…
This is my answer to the OEM Atomos drive caddy. I hated having to install and remove screws just to use new SSDs, so I designed a surprisingly secure caddy with no need for tools. Printing Tips: No supports necessary - brim is…
Model This is an SSD adapter for the Atomos Ninja Flame, it allows you to use standard 2.5" SSD's. They slide in perfectly and snugly making it much easier to use. Print Settings Print this with any sturdy filament, supports are not…
Own design, Printed with ender 3. 0.2 layer height Recomended to have enough botom layers to be sure its firmly mounted on the frame
A couple of years ago, I purchased a Sony NEX-FS700 second-hand for some random filming projects. However, I did not actually receive the rosette handle for the camera. Leaving a bit of a void in the overall look of it. Initially, I…
The MHz Tomoscopy project website https://tomoscopy.eu/ The MHz Tomoscopy project has received funding from the European Union’s Horizon Europe research and innovation program under grant agreement No. 101046448
Printing with BambuLab P1S, ASA Prime (AzurFilm) resolution BambuLab 0.16 strenght , supports only on bed
beautiful tomos keychain, numbers 1 and 2 need to be glued together.
For all my vertical reel shooter, It is a vertical sunhood. I know its kinda stupid, but I find it uncomfortable when I use standard sunhood for vertical shooting and I can't the entire screen. This model is a remix of DoNotLeaN…
Model This is a loupe for the Atomos Samurai Blade which uses components from a GGS 3X Loupe. The only real issues is that it does not fully cover screen and should be redesigned with 2X Optics. This description is a work in progress and…
Magnetic carrying case for an atomos zato connect. Held together with 4 8x4mm Magnets found here. Affiliate Link: https://amzn.to/3WvcYKc
I was inspired by this case, which unlike the full size cases allows the vents on the back of the Ninja to breathe, but the Crucial MX500 that I have didn't have the same board layout. This also keeps the original chassis as a heatsink…
Model This is a screen cover for the Atomos Samurai Blade but also works with the HDMI Blade. Print Settings I would highly recommend printing this with a flexible or soft filament such as PETG, ABS, Nylon or a specifically a TPU. Tape…
Custom intake manifold for Tomos A35 moped / scooter. For use with stock (or similar) cylinders. I'm running an airsal cylinder, but I know it is the same as a stock one. It has an internal diameter of >= 14mm. Carb position is exactly…
There's tiny little knubs on the Atomos SSD caddy to allow using a finger nail to pull them out. I took inspiration from an SSD handle I saw but redrew things from scratch. First got the idea from DLSR Video Shooter's VideoDock. Needs 2…
With the addition of the NPF plate, the caddy is a little tougher to get in, but once its in - it's very tight.
Cover for the SDI ports for the Atomos Shinobi SDI. Print with TPU
tomos BT digital speedometer
Nozzle - 205C° Bed - 50C° Infill 25%
među prvim tomosovim trkaćicama
Tomos A35 and A55 moped clutch cover gasket OEM # 232971 one complete gasket stl and the option to print 1/2 and glue together Ive been printing it in TPU
Quickly designed this part to cover up the exposed metal on the left pedal's mount position when it is removed. It's a perfect fit size-wise, but may require some glue to be firmly held on. Printed with PETG to protect from wear-and-tear…
i suggest to print in pla, blue base and white letters. u can use multicolor printer or use pauses
Designed to cover up your deleted oil injection pump on early Tomos A35 moped engines where the oil injection pump cover has an 85mm diameter. This design is too small for newer A35 and A55 flywheel covers but there's another model on…
My old shifter rubber was falling apart so instead of buying a new one i decided to use some of the TPU i had to make my own. Of course it should go without saying you should print using TPU or other flexibles. My reccomendation is to use…
This mount is designed specifically to securely and practically attach a SanDisk SSD to the Atomos Ninja V monitor/recorder. It is the ideal solution for filmmakers looking for a budget-friendly, compact, and reliable alternative to…
This model is designed to fit Tomos fork braces/fender mounts. Due to its size, I split it into two halves, so you’ll need to print two copies, glue them together, and drill your own mounting holes. The fork brace will hide the seam once…
a simple model that i used to increase the hole in my tomos moped crankcase to 51mm
