Liczymy pasujące modele…
Tricycle Fiat500 (model2 of 5) Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 -200 Filament material: PLA Note: Trim can without support!
Tricycles VW beetle (3e model of 5) Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 -200 Filament material: PLA Note: Trim can without support!
Tricycle Triumph TR2 (5e of 5 models) Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 -200 Filament material: PLA
This is a Steerable Wind-up Spring Tricycle. Max steering angle is ~60°, but it is recommended to stay within 30° for smooth operation. Angles exceeding 30° may hinder movement. Performance is limited on high-friction or uneven outdoor…
オリジナルの三輪1/12電動ラジコンカーです。 BOMも詳細な説明もないSTEPファイルぶん投げスタイルですんません。 まだチューニング等は出来ておらず、走行動画を見てもらえば分かりますが、リアの挙動がいまいちでコーナーで荷重が抜けるとスピンしがちです。 制作中のツイートを下記にまとめています。 https://min.togetter.com/zBp4x5F An original 1/12 scale electric RC three-wheeler. Sorry…
This worked well made from Nylon, though I wouldn't be afraid to try them out of other plastics. In a worst case scenario, they wear quickly, and and need to be replaced again.
Replacement axle linkage for the front wheel on a radio flyer tricycle. Specific models are unknown as the one I was repairing was from the 90s, but based on looking at a modern tricycle this should be easily modified to repair most types.
Simple adapter block to drop the childrens' bike rear-axle 5 cm, so younger children can start using the bike. Printed in PETG, with some extra perimeters and infill easily strong enough. Model contains M8 screw thread.
support part for pedal locking mechanism on Chicco Ducati as the plastic wheel would always slide out on its own.
Threw together this rear step replacement in TinkerCAD after the original one rotted and broke off my son's tricycle. It is keyed so that the middle piece is held in place by the outside pieces. I made a minor error in the model so you do…
I recently got my niece a trike. Unfortunately, the positioning of the handles allows her to easily scrape her hands if she gets too close to a wall or other obstacles. Luckily, I had some ASA filament I wanted to test, so I designed this…
I needed a clamp to hold my freewheel in place on my kent tricycle. May work on other tricycles, I don't know what axle size they would have. It uses M3 screws and nuts. The nuts may be optional depending on what material you use or what…
Adaptive pedal for Kinder King Kids Tricycle (Amazon link below) Designed for a tool-free perfect fit. Pedal and top bracket will need to be mirrored in slicer. Two adapters are required for each side. One adapter goes on upside down, one…
Since my Carello was missing its wheel caps, i borrowed an original one from a friend and remade it myself.
Simple adapter block to drop the childrens' bike rear-axle 5 cm, so younger children can start using the bike. Printed in PETG, with some extra perimeters and infill easily strong enough. Model contains M8 screw thread.
I recently got my niece a trike. Unfortunately, the positioning of the handles allows her to easily scrape her hands if she gets too close to a wall or other obstacles. Luckily, I had some ASA filament I wanted to test, so I designed this…
I designed a replacement pedal for my kiddos tricycle. It made a nice training for Fusion 360. Print Settings Printer: Print Rite DIY Rafts: No Supports: Yes Resolution: 0.25 -0.35 Infill: 80% Notes: Printed in PLA but ABS would be a…
Adaptive pedal for Kinder King Kids Tricycle (Amazon link below) Designed for a tool-free perfect fit. Pedal and top bracket will need to be mirrored in slicer. Two adapters are required for each side. One adapter goes on upside down, one…
Pedal fits for small bikes with non-removable old pedal. More durable then original. You just need four M3x14mm screws per pedal.
Spacer/pedal to replace broken one. Print Settings Printer: Anycubic i3 mega UltraBase Rafts: No **Supports:** Yes Resolution: 0,15 **Infill:** 70 Notes: ABS, use brim for safe adhesion. Category: Replacement Parts
I designed a replacement pedal for my kiddos tricycle. It made a nice training for Fusion 360. Print Settings Printer: Print Rite DIY Rafts: No Supports: Yes Resolution: 0.25 -0.35 Infill: 80% Notes: Printed in PLA but ABS would be a…
Old brittle rims? Replace with new multi spokes. I think it is a Stiga cycle, but may fit many others as well. Compare measurments: Front rim 148 mm inner / 166 mm outer edge / 23 mm, 10 splines axle Rear rims 121 mm inner / 131 mm outer…
Replace cracked and worn out handlebar grips with these. Print with squishy TPU. Fits 3/4" diameter handlebars
Grandkid needed a new tricycle bell. Tube diameter 16mm, bell inner 22mm. Step: Measure OD Ø16 and ID Ø22mm. Step: Start TinkerCad, draw a Ø22mmx18 cylinder, another two Ø24x3mm cylinders, arrange the two at to and at end, center align…
I needed a custom trophy for a tricycle race. I scanned in a tricycle, which looked hideous, so I modeled in from scratch in TinkerCAD, using the scan as a guide.
Tricycle Ford model A Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 -200 Filament material: PLA Note: Trim can without support!
Tricycle Mini (4e of 5 models) Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 -200 Filament material: PLA Note: Trim can without support!
