Liczymy pasujące modele…
I don't know if I should even share these, as they are far too awesome for the general public to handle. BUT! I think Optimus would want it this way. So, here they are: AUTOBOT BADGES FOR YOUR VANAGON! These fit an '88 VW Vanagon 2WD (I…
It's nice to have a Volkswagen Vanagon. But as they are gaining experiance (aka become old), there occure a few technical problems here and there. Very common is that the odometer stops counting the kilometers (yes, metric!). Usually, the…
Lo hice muy grande por accidente a un tamaño de 10% debería de estar bien. Scale to 10%.
This is another little project for the Volkswagen campervan: The dashboard phone stand. Funny enough, my 1990 Bluestar Multivan has neither Apple Carplay nor Android Auto. Just a little outdated, you think. Well, there is more! As we have…
Since one pin broke of my climate control cover, I designed these pins as replacement. I've removed the second pin with a dremel and replaced both pins with these printed ones. The height of the hole differs in my case. Therefore, there…
Print with PETG Change color on Z=3,60
Print from TPU Infill can be modified in both ends to 100%
This is a replacement interior fridge vent for a VW Vanagon Westfalia, with two 12V power socket mounts. The 45 degree sockets are necessary if you have something other than a stock fridge, since the aftermarket fridges take up…
Replaces defroster vents in VW Vanagon and Synchro vans, made to same dimensions as original vents. Materials Printed components Printing PLA - If you are planning on running heat through the vents use a filament with higher temperature…
Print with ABS. Dremel, Glue, Done.
Die IKEA-Leuchte “Rolfstorp” eignet sich hervorragend als günstige Ersatzleuchte für die original verbaute Transistorleuchte. Mit diesen Befestigungs-Clips lässt sich die Leuchte auch einfach wieder abnehmen um diese z.B. im Notfall im…
This is a remix of DaGaLife's Tiguan wheel cap, for a VW Vanagon. Scaled up for a 56mm hole. The Vanagon's rear axle sticks out significantly past the wheel, so a tall cap is necessary to cover it. It holds OK by itself, but I added a…
This is a small plastic shield to make it easier/safer to connect jumper cables to the + terminal. The frame/body is - so sparks/shorts are an issue. Made in TinkerCad, printed on an AnyCubic i3 Mega S.
I found this video on YouTube to be incredibly helpful when trying to fix shifting issues in my Vanagon. The poster uses a piece of wood cut down to 23mm to make the spacer. I didn't have a piece of wood, but I did have a 3d printer. The…
Clamp to secure the gas throttle to the diesel pump. Lost my original one so i designed a printable one.
Just a replacement door stopper for a Vanagon T3. Print it in flexible filament. Included is the STL file and 123D Design file. Category: Automotive
Edit: Added June 12 2026: Split into 3 parts for smaller printers. Edit2: Added June 22 2026, added flanges the 3 part split pieces to make it easier to glue together (more surface area at the joint) These valances are infamous for…
This is for the Gen 4 Smallcar AC dash kit. I didn't like the way that the air vents for the dash were hard up against the brake booster, and the subsequent super tight curves required. I have the large BMW booster, so its probably better…
The auxiliary heater under the bench of the T3 Multivan is notorious to fail (I learnd after mine failed). I did the reasonable thing: I restored the heating unit and … did not install it again (I don't thend to use the car in winter). So…
VW T3 Vanagon loudspeaker fitting / Halter Lautsprecher Decke VW T3 Caravelle 251035429 / 8 601 360 017
The original speakers of my 1990 T3 Mulitvan Bluestar are tired. Who would complain after 35 years of service. Apperantly they have an odd shape that is not easily available nowadays.. The outer diameter was 122, the bolt sicle diameter…
The original Vanagon charcoal emissions canister has been NLA for a while. A replacement is available (1H0201801C) but the bottom vent is quite different. This adapter makes it easy to hook up a ¼" host in order to plumb it into the air…
I would recomment printing it atleast in PETG so it doesnt melt in the sun
I used polyflex TPU95 to print. I upgraded my fridge on my vanagon westfalia and needed to block the hole left behind after the fridge was removed so I printed this. on the picture old and new
This is a vent guide for the dash vents on a VW Vanagon. I found the model years ago, printed it in PLA, but when I went to reprint it in PETG, I couldn't find it online. Turns out I had never thrown out the STL but since I can't find it…
Closes the holes i needed to cut into the speaker housings of my Caravelle GL in order to replace the old, defective "Blaupunkt" speakers with those new "Kicker" ones. Nearly any 79mm speaker should fit. Glued everything together with 2K…
Replacement Gas Stove Knob (Westfalia, Vanagon, T3). I printed in PETG. Until now no issues with too much heat. Print Instructions Print on top. No supports needed
I broke another cabinet latch on my 40 year old van, so I decided to print a replacement for the broken part. Take the latch apart with the 3 screws, then use pliers to take out the 2mm pins holding the broken part in place. Put in the…
After a sealing ring of the rear auxiliary heater of my VW Multivan Bluestar failed, dumping the entire coolant into the carpet, I removed the unit. Obviously, I want to protect the plug to be able to reinstall the unit, if I ever want to…
This is a replacement part for the arm that helps move the mirror for the Volkswagen Transporter T3 Vanagon. Prints with only supports on the board. Second version with a specific cut to allow the triangular lever to move through the part…
Using an aluminum tube 12x10mm To assemble, heat the tube with a hot air blower and press on the fittings. Retaining clip for rod is not included (commercially available).
Made a Version with D32mm for larger holes because it seems there are Vanagons with 28mm and with 32mm.
My rig has enough holes in it so instead of drilling more I made this. Sized for PETG Bolts are M3 anything between 7-12mm should work, #6 should work as well The tension fit comes from the 4 "bumps" (shown in the last pic) that protrude…
Bracket to mount a contact switch for the brake pedal on a Vanagon. I used this to replace the pressure switches on the original brake system due to converting to an electric booster with a different master cylinder. I used M2.5 bolts to…
mini model of the t3 camper volkswagen
VW 1984 Vanagon 50/50 Sliding window AC exhaust vent for a 6inch ac exhaust hose. Not the prettiest but functional. I had to cut into 4 in slicer so i could print on my Flash-forge Adventurer 5M Pro & then used 3d printing super glue on…
This is a phone mount that installs in the stock ashtray location on Volkswagen Vanagons.. This uses M6 nut/bolts was printed in ASA.
Ring to hold rear speaker in Westfalia T3, Ring screw on the speaker to hold int in place
These are wheel caps for Mercedes CLK wheels when mounted to a Volkswagen Vanagon. These should be printed in the orientation shown otherwise the tab will break off. I printed these in ASA with HIPS as a support interface.
Replaces defroster vents in VW Vanagon and Synchro vans, made to same dimensions as original vents. Materials Printed components Printing PLA - If you are planning on running heat through the vents use a filament with higher temperature…
Bracket to mount a contact switch for the brake pedal on a Vanagon. I used this to replace the pressure switches on the original brake system due to converting to an electric booster with a different master cylinder. I used M2.5 bolts to…
