44 modeli
The yashica 44 is an old twin lens reflex camera designed for 127 film. This film is like the widely available 120 film, but with a 4cm wide strip of film instead of 6cm. This makes it challenging to use today, as film is hard to find…
Yashica 124G Lens cap. I printed it in PLA with 0.4mm nozzle and 0.2mm layer. It fits snug!
Bay 1 lens/sun hood, for all cameras with bay 1 bayonet. This was designed in INCHES. Have to convert to mm for printing (2450%)
Yashica Electro 35 Battery Adapter /Yashica MG-1 (etc etc) After a sucess of previous model (first upload on 5th december 2019), I decide to improve the model by reinforced the adpater. If you have an old camera that uses mercury cell…
This adapter lets you install a commonly available PX23 6 volt battery in a Yashica Electro 35 GSN camera. They originally used a 5.6 v mercury battery. It may fit in other cameras as well. Very simple print, no supports needed. I printed…
This is a body cap to fit the Contax-Yashica CY-Mount. It uses the standard locking pin in the camera to latch in place, so to release you must hold down the lens release button. Knurled edge to help in attaching/detaching from the…
Just added a simple logo. Works with mano Yashica TLR cameras (Mat 124 / 124G etc) Category: Electronics
I recently acquired my first vintage TLR camera, a Yashica Mat-124G. Since I haven't yet gotten used to the viewfinder being mirrored, I find it particularly difficult to control the tilt of the camera to capture horizontal or vertical…
Keep the filter on and place this lens cap on to protect it. Suitable for TLR Bayonet 1, Aires reflex, Rolleicord, Rolleiflex and others. Filament: PETG Which one to print? From left to right: Lenscap for Rolleiflex with bay 1 filter on,…
I bought this camera a few weeks ago and it came with a metal lenscap but I found it was incredibly difficult to use as it required a lot of force to snap onto the photo lens, so I made a copy of it but changed some things to make it fit…
I have this broken Yashica for sometime and now since I have access to 3D printer and Fusion 360 software I was able to successfully achieve this conversion. The focus helicoid is a simple M25 thread and it was inspired by the early leica…
This is a compact, 90-degree cold shoe adapter specifically designed for the Yashica Mat-124G . The side-mounted accessory shoe on these cameras usually leaves external light meters facing sideways. This adapter reorients the shoe by 90…
Following my design for Yashica Electro 35 CC grip I've decided to make this, a simple to print and comfortable grip for legendary Yashica Electro 35. It mounts with a simple ¼" camera screw, often called “tripod screw”. I'm currently…
I have always found focusing with my Yashica Electro35 rather cumbersome and the mechanism to be kind of sluggish. While this may be attributed to my camera needing some CLA, i could not understand why the original focustabs screwed into…
Gegenlichtblende / Sonnenblende / Störlichtblende / Streulichtblende für das Yashica ML 50mm f2. Gewinde M52 x 0,75. Kann aufrecht stehend mit der großen Öffnung nach unten ohne Unterstützung gedruckt werden. Für den Teil mit dem…
Adaptador para utilizar baterías 4LR44 en las cámaras Yashica Electro 35. Hace falta algo de maña para “fabricar” el conector inferior. Yo lo hice reutilizando el de un mando viejo de TV (ese que parece un muelle) soldado al cable de…
Version 2 – Lens Cap for TLR (Bayonet 1) with Mounted Filter With this design you can keep your filter on and simply place the lens cap over it to protect your TLR lens. Compatible with TLR Bayonet 1 (Aires Reflex, Rolleicord, Rolleiflex…
This adapter serves only for aesthetic purposes. The truth is, I couldn't find a way with sufficient focus for this machine's body. What happens is to have a focus, the lens would have to be closer than the body's own entry point, which…
Little mod for a old Yashika cam, so its possible to mount a little flash to the cam. I'm using a cable to connect it to the camera, because the cam does not have a hotshoe. The adapter is mounted on the tripot thread.
Self-timer Lever for Yashica FR-1 (and probably whole FR and FX series). Mine broke, so I had to squeeze it to advance the mechanism. It ended up breaking in two, so I made a printable model. All other FR type cameras FR II and FX series…
You don't see many Yashica Rapides and I think the lens cap would be almost impossible to replace. Here's my “out and about” version. If I loose it, I'll print another. I printed it upright with support in PLA and it came out nicely and…
Here is a model I made for my Yashica camera. The cavity is based on the maximum published diameter of the battery, so one at the lower tolerance may wiggle a bit. Use a spring from a pen to bridge the gap of the contacts. Make sure you…
Just print normal
Simple camera grip which mounts with standard ¼" screw. Fits Yashica Electro 35 CC and CCN Wide. Took around 2 days of testing. I tested different designs on the web and all of them have to little clearance between lens and the grip and…
I love my Electro 35 and its original leather case, but I wanted one that I wouldn't be worried to damage, so I designed my own! My camera is an Electro 35 GS, but from what I can see online the other models in the Electro 35 line seem to…
Use this slide-on vented lens hood on your Yashica Electro 35 GX (and probably other models). One model extends 15 mm above the metal rim, the other 13 mm. I did not yet test for vignetting on the longer one. Feel free to contact me for…
Replacement rear filter holder for Yashica Reflex super telephoto lenses. Made to fit generic 37mm filters. I used these from aliexpress https://aliexpress.com/item/1005004547509306.html
Requires a 1/4 20 and two M2 Socket head screws to fit to the camera. I also included a replacement focus nub for better grip and one handed winding, focus and shooting for the brave.
A lens cap for the Yashica 35MF
Replacement tab for the Yashica Electro 35 GX (and probably related models). Print at 0.15 mm layer height with fuzzy skin on the outside (smart fill on prusaslicer works great when adjusting the angle properly) Peel off the old tab, and…
Yashica mat 124-G double lens hood for bay 1
A simple grip that the camera can slide into. The fit is snug. I don't find I need to secure it with a screw, but I've made a hole in the bottom if you want to secure it with a plate. This is currently my 3rd iteration, but I may make…
PVS-14 to Yashica electro 35 gsn adapter. I have included f3d and step file so feel free to modify base to use for other camera types. remix are welcome for print settings I used 6 walls and 0.08 layer height for camera part and 0.16 for…
The lens cap doesn't interfere with the lens movement when you turn the camera on/off or fiddle with the zoom, so it should be safe to use. I printed mine in TPU 95a HF and it's easy to put while still holding on well. I went through 3…
Simple helicoid for fuji x to adapt any lens to. feel free to mod. push the cylinder in the mount so that infinity is focused.
This is an enhanced hand grip for the Yashica FX-3 camera that I modeled. It has two screws to attach it to the camera using the camera mount screw hole. One can be screwed in by hand and the other is smaller and should be able to be…
3d scan of a Yashica T5 battery door. Will not fit a T4. Mesh still needs work, if someone puts in the effort please upload a remix with the same license :)
Yashica Samurai X4.0 Viewfinder Cover / Block (TPU) A custom replacement eyepiece/viewfinder cover for the Yashica Samurai X4.0 half-frame camera, designed to block light when taking timer shots. Replaces the prone-to-breaking original…
I created this tool to unmount the inner lens of a Yashica Mat124G. I used it on the taker lens, but it should also work for the view lens.
A simple grip that the camera can slide into. The fit is snug. I don't find I need to secure it with a screw, but I've made a hole in the bottom if you want to secure it with a plate. This is currently my 3rd iteration, but I may make…
This is a compact, 90-degree cold shoe adapter specifically designed for the Yashica Mat-124G . The side-mounted accessory shoe on these cameras usually leaves external light meters facing sideways. This adapter reorients the shoe by 90…
Requires a 1/4 20 and two M2 Socket head screws to fit to the camera. I also included a replacement focus nub for better grip and one handed winding, focus and shooting for the brave.
Keep the filter on and place this lens cap on to protect it. Suitable for TLR Bayonet 1, Aires reflex, Rolleicord, Rolleiflex and others. Filament: PETG Which one to print? From left to right: Lenscap for Rolleiflex with bay 1 filter on,…
