P
PrintablesDerok123
Yokomo YD2 SXII Battery Holder (RC Drift)
Držák baterie na podvozek Yokomo YD2 SXII, jednoduchý a funkční koncept. I po instalaci je stále možné použít odklápěcí držák baterie.
- Pobrania
- 91
- Polubienia
- 12
- Ocena
- 0
Wyniki wyszukiwania: yokomo
Liczymy pasujące modele…
P
PrintablesJacyk
30mm 25mm Fan Air Funnel RC Car drift yokomo traxxas xray schumacher
Hi, It's my air funnel for 30mm and 25mm fan.
- Pobrania
- 597
- Polubienia
- 76
- Ocena
- 5
P
PrintablesRoadsideRC
RC Drift Magnetic Body Mount - for Yokomo YD2-Z RTR (Front and Rear)
Simple magnetic body mount for the Yokomo YD2 vehicles. I specifically made this for the YD2-Z RTR model. You will also need 12mmx3mm magnets, and some 1.5mmx15mm screws to attach it. It is designed for the screw to go through the factory…
- Pobrania
- 232
- Polubienia
- 29
- Ocena
- 0
P
PrintablesMrNeedlemouse
Yokomo YD2 Magnet Body Mount, perfect fitment!
Designed to be easily adjusted if needed for the perfect fitment, and works pretty well for walltaps due to the deep magnet cups! Additional hardware needed below, and pay attention to print orientations and mirroring the rear mounts. No…
- Pobrania
- 190
- Polubienia
- 19
- Ocena
- 0
P
PrintablesFabian
Car stand 1/10 Offroad Yokomo
Car stand for 1/10th scale offroad rc cars. This car stand has a Yokomo branding. You also need six M3x10 screws and 6 nuts to screw the two halfs together.
- Pobrania
- 107
- Polubienia
- 15
- Ocena
- 5
P
PrintablesPMendoza
Extension handle for Yokomo turnbuckle wrench
Extension handle for Yokomo turnbuckle wrench
- Pobrania
- 70
- Polubienia
- 7
- Ocena
- 0
P
Printablessp_cecadet
Magnetic mounts for yokomo body posts
magnetic body mounts that fit yokomo posts. Use existing body pins to secure to body posts. mounts them selves allow quite a bit of adjustment in height. These things are rough I just made them quick and sloppy as a stop gap but dammit…
- Pobrania
- 70
- Polubienia
- 8
- Ocena
- 0
P
PrintablesdefMondo
Yokomo YD2SX3 esc wiring stealth mount
Mount plate to mount esc on rear difuser with wiring underneath right rear out drive. This mount allows you to run the power, motor, esc signal and sensor wiring underneath a place and underneath the right rear out drive on the YD2SX3…
- Pobrania
- 53
- Polubienia
- 8
- Ocena
- 0
P
PrintablesMartin Subie
Battery holder for short LIPO - YOKOMO YD2
Pad for a short battery to prevent movement. If you want a colored logo, it is necessary to change the color of the filament.
- Pobrania
- 53
- Polubienia
- 2
- Ocena
- 0
P
Printablesofficepizzaparty
TT-02 Gyro Clip - for Yokomo DP-302 V4
A simple mount to center your gyro on the chassis of your RWD-converted Tamiya TT-02. Includes a wall to route cables along the inside of the clip. Notes: Mount to chassis as pictured using an extra Tamiya 3x10mm "MA2" screw Print on the…
- Pobrania
- 24
- Polubienia
- 1
- Ocena
- 0
P
PrintablesYoko
Experimental toolhead by Yokomo
List of materials BMG set Idler arm from a sherpa mini M3 inserts with an diameter of 4.1mm (Mellow brass inserts were used) Notes: chop down the heatsink for those measurements
- Pobrania
- 13
- Polubienia
- 1
- Ocena
- 0
P
Printables
TT-02 Gyro Clip - for Yokomo DP-302 V4
A simple mount to center your gyro on the chassis of your RWD-converted Tamiya TT-02. Includes a wall to route cables along the inside of the clip. Notes: Mount to chassis as pictured using an extra Tamiya 3x10mm "MA2" screw Print on the…
P
Printables
Yokomo rear bumper
Simple rear bumper that protects the ESC and can be used to carry the chassis. I recommend at least 3 perimeters and 50% infill.
P
Printables
Underglow Yokomo SD2.0 LED strip holder
I have created a full set of LED strip holders for the Yokomo SD 2.0 1:10 scale RC drift car. Tested on a real model. More information about the electronics, wiring, software and integration with the Futaba transmitter is available on…
P
Printables
Yokomo SD2.0 RD2.0 rear body holder
Magnetic rear body mount / holder for the Yokomo SD_RD_2.0. There are a few different variants for different bodies. Adjusted angle. M3 screws mounted.
P
Printables
Yokomo YZ10 Front Knucle
Yokomo YZ10 91 Works Front Knucle Print Settings Printer Brand: Zortrax Printer: M200 Rafts: Yes Supports: Yes Resolution: .09 Infill: 100 Category: R/C Vehicles
P
Printables
Battery tray holder for yokomo yd2z.
Securely cradle your Yokomo YD2Zs power source with our battery tray holder, optimal performance on every twist and turn! This is designed to be used with heat set thread inserts. these ones: https://amzn.to/3JR0gh6 Note these are not…
P
Printables
Rear ESC mount for yokomo yd2z
Two base holders. Both models use thread serts, these ones specifically, but any 3mm based one would work: https://amzn.to/3WvNU5w One holder is flat without nubs and sad. It is sad because it is designed to be used with VHB. Look how sad…