1 / 14
Lack Enclosure for the Lazy and Larger Printers — image 1
1 / 14

Lack Enclosure for the Lazy and Larger Printers

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

An enclosure designed for the lazy or large printer.

Rating
0 / 5
Likes
1
Downloads
6
Makes
0
Views
49
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

I really liked the Lack designed printing farms that I have seen in other setups. In a desire to expand my own printing capacity I needed to find a solution that would house the enclosures I was using and was a little more simpler to put together. 

Welcome the Lack Enclosure for the Lazy(me) and Larger Printer areas.

A stable and strong shelving system that provides 2 surface areas measuring 81cm x 55cm x 50cm (HxDxW) and 1 surface area measuring 81cm x 55cm x 44cm. I am able to store my filament on top with no issues of sagging or destabilisation. 

Requirements

  • 6 Lack Tables
  • 4-8 M8 40mm Screws
  • A second person to help lift during assembly and placement

Print Quantities

  • 8 - Lack Table Leg Connector
  • 8 - Lack No Leg Support
  • 8 - Lack No Leg Support Cap
  • 8 - Leg Connector Pin 

Print Recommendations
(you know your printer best so use what you know will work for you)

  • Print the Leg Connector Pins together on a raft at 100% infill
  • Use PLA+ or PETG (I used PLA+)
  • Settings
    • Infill: 20% Cubic
    • Wall Line Count: 3 

Build Instructions

  1. Construct 4 Lack tables with only 2 legs on the same side (aka next to one another)
    1. Use the “Lack No Leg Support Cap” between the table and the leg. 
    2. Use the hardware that came with the table
  2. Construct 2 Lack tables with all 4 legs
    1. Use the “Lack No Leg Support” between the table and the leg.
    2. Ensure the tapered end is facing outward of opposing sides. (2 face one direction, 2 face the opposite direction) They should be reaching beyond the table top.
  3. Place the a 2-legged table on either side of the one of the 4-legged tables. 
    Use a flat surface space where you can complete the setup without moving it.
    1. The 2 legs of the 2-legged table will be on the outside.
    2. The overhand support on the 4-legged tables will match up with the holes of the missing legs on the 2-legged tables.
    3. Use the M8 Screws to attach the overhang to the 2-legged table in the open leg hole. You can also use the foot pegs that come with the Lack table in a pinch, it just wont be as sturdy.
  4. Repeat with the other two 2-legged table and 4-legged table.
  5. Insert the "Leg Connector Pin" in the leg holes of one set. You may need to lightly tap, LIGHTLY, with a rubber mallet or hammer if you are careful to sink them in.
  6. Place the “Lack Table Leg Connector” over the pinned legs. They should slide on easily.
  7. You will then lift the unpegged tables and carefully turn the tables right side up and place them over the “Lack Table Leg Connector” of the other tables. (Recommend 2-people, torqueing the contraption can destabilase the connections at this point)
  8. Once the legs are aligned you can then use a rubber mallet or hammer with a towel, on the top part of the table to secure the legs together. Ensure all legs are sunk into the connectors and the top is level.
  9. The Lack Enclosure should feel secure and have minimal wobble. (I had zero wobble) You can then move it to your desired location. (Recommend 2-people, because it is rather heavy and awkward)

TA~DA!! Enjoy your new printing station! And if you make it, I'd love to see your setup!
 

Tags