Lack Enclosure for the Lazy and Larger Printers
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
An enclosure designed for the lazy or large printer.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 6
- Wydruki
- 0
- Wyświetlenia
- 49
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
I really liked the Lack designed printing farms that I have seen in other setups. In a desire to expand my own printing capacity I needed to find a solution that would house the enclosures I was using and was a little more simpler to put together.
Welcome the Lack Enclosure for the Lazy(me) and Larger Printer areas.
A stable and strong shelving system that provides 2 surface areas measuring 81cm x 55cm x 50cm (HxDxW) and 1 surface area measuring 81cm x 55cm x 44cm. I am able to store my filament on top with no issues of sagging or destabilisation.
Requirements
- 6 Lack Tables
- 4-8 M8 40mm Screws
- A second person to help lift during assembly and placement
Print Quantities
- 8 - Lack Table Leg Connector
- 8 - Lack No Leg Support
- 8 - Lack No Leg Support Cap
- 8 - Leg Connector Pin
Print Recommendations
(you know your printer best so use what you know will work for you)
- Print the Leg Connector Pins together on a raft at 100% infill
- Use PLA+ or PETG (I used PLA+)
- Settings
- Infill: 20% Cubic
- Wall Line Count: 3
Build Instructions
- Construct 4 Lack tables with only 2 legs on the same side (aka next to one another)
- Use the “Lack No Leg Support Cap” between the table and the leg.
- Use the hardware that came with the table
- Construct 2 Lack tables with all 4 legs
- Use the “Lack No Leg Support” between the table and the leg.
- Ensure the tapered end is facing outward of opposing sides. (2 face one direction, 2 face the opposite direction) They should be reaching beyond the table top.
- Place the a 2-legged table on either side of the one of the 4-legged tables.
Use a flat surface space where you can complete the setup without moving it.- The 2 legs of the 2-legged table will be on the outside.
- The overhand support on the 4-legged tables will match up with the holes of the missing legs on the 2-legged tables.
- Use the M8 Screws to attach the overhang to the 2-legged table in the open leg hole. You can also use the foot pegs that come with the Lack table in a pinch, it just wont be as sturdy.
- Repeat with the other two 2-legged table and 4-legged table.
- Insert the "Leg Connector Pin" in the leg holes of one set. You may need to lightly tap, LIGHTLY, with a rubber mallet or hammer if you are careful to sink them in.
- Place the “Lack Table Leg Connector” over the pinned legs. They should slide on easily.
- You will then lift the unpegged tables and carefully turn the tables right side up and place them over the “Lack Table Leg Connector” of the other tables. (Recommend 2-people, torqueing the contraption can destabilase the connections at this point)
- Once the legs are aligned you can then use a rubber mallet or hammer with a towel, on the top part of the table to secure the legs together. Ensure all legs are sunk into the connectors and the top is level.
- The Lack Enclosure should feel secure and have minimal wobble. (I had zero wobble) You can then move it to your desired location. (Recommend 2-people, because it is rather heavy and awkward)
TA~DA!! Enjoy your new printing station! And if you make it, I'd love to see your setup!