Prusa XL Top Case Filament Holder for abrasive Filaments
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Prusa XL Top Case Filament Holder for abrasive Filaments
- Rating
- 5 / 5
- Likes
- 13
- Downloads
- 36
- Makes
- 1
- Views
- 383
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Prusa Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial
***** English *****
The project started when I was having problems with abrasive filaments. Initially, it was supposed to be a simple top-loading system that required as little PTFE tubing as possible. But then I modified it a bit more and created a version that also allows for the filament sensor to be mounted. I also created the option to simply screw in 10mm PTFE fittings. This allows you to print with the filament sensors turned off and doesn't require as much modification.
It was printed with 20% infill made of PETG (Prusament Galaxy Black and Orange). No Supports.
To attach it, remove the five plastic clips on each side that hold the plexiglass. They are replaced with five M3x10mm screws and five M3 hex nuts. This keeps the plexiglass in place without having to drill any additional holes.
The rest is assembled as shown in the photo. I found that the combination of a real ball bearing on the outer edge and a fake plastic bearing on the inner area works best for me. I also added three M8 nuts on the inside to keep the roller at a certain distance from the bracket.
If you want to attach the filament sensor, keep in mind that the cable needs to be extended.
In the pictures there are 4x TPU and 1x PLA Glow with quite a bit of friction resistance. It wouldn't be easy to print with the original PTFE guide. Almost no problem with this one. Unfortunately for me, Head 1 likes to wrap the red TPU around the gear. But that's another problem.
Other requirements:
M8 threaded rod top: 27 cm
M8 threaded rod side: 18 cm
55 cm PTFE for each Head (4mm outside)
Ball bearings (608 ZZ ball bearings)
M3x10 screws and nuts
***** German *****
Angefangen hat das Projekt, als ich Probleme mit abrasiven Filamenten hatte. Zuerst sollte es eine einfache Zuführung von oben werden, bei der möglichst wenig PTFE Schlauch nötig ist. Doch dann habe ich etwas mehr umgebaut und eine Variante erstellt, bei der auch der Filament Sensor dran montiert werden kann. Zudem habe ich die Möglichkeit erstellt, einfach nur 10mm PTFE Fittings reinzuschrauben. So kann man mit ausgeschalteten Filamentsensoren drucken und muss nicht so viel umbauen.
Gedruckt wurde es mit 20% Infill aus PETG (Prusament Galaxy Black und Orange). Keine Supports.
Um es zu befestigen, werden die pro Seite jeweils die 5 Plastik Klammern entfernt, die das Plexiglas halten. An Ihre stelle kommen 5x M3x10mm Schrauben mit 5 M3 Sechskant Muttern. Damit bleibt das Plexiglas in Position, ohne dass extra Löcher irgendwo gemacht werden müssen.
Der Rest wird so wie auf dem Foto zusammengebaut. Ich habe festgestellt, dass die Mischung aus einem echten Kugellager am äußeren Rand und einem Plastik Fake Lager im Inneren Bereich für mich die beste Kombination ergibt. Des weiteren habe ich innen jeweils 3 M8 Muttern dran geschraubt, damit die Rolle einen Abstand zu der Halterung hält.
Falls man den Filamentsensor anbringen möchte, ist zu bedenken, dass das Kabel verlängert werden muss.
Auf den Bildern sind 4x TPU und 1x PLA Glow mit ziemlichem Reibungswiderstand. Mit der original PTFE Führung wäre das nicht so einfach zu drucken. Mit dieser fast kein Problem. Denn leider wickelt bei mir Kopf 1 das rote TPU gerne um das Zahnrad. Aber das ist ein anderes Problem.
Sonstiger Bedarf:
M8 Gewindestange oben: 27cm
M8 Gewindestange seitlich: 18cm
Pro Kopf jeweils 55cm PTFE Schlauch (4mm außen)
Kugellager (608 ZZ ball bearings)
M3x10 Schrauben und Muttern