1 / 18
Electrical Distribution Box and MIDI Fuse Holder for Boat/Leisure Yacht — image 1
1 / 18

Electrical Distribution Box and MIDI Fuse Holder for Boat/Leisure Yacht

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

An electrical distribution box with two bus bars, MIDI fuses and seven terminals connections.

Rating
0 / 5
Likes
6
Downloads
17
Makes
0
Views
222
Reviews
0

Updated at source:

Model information

Category
Automotive
License
Creative Commons — Attribution — Share Alike

Summary

This is an electrical distribution box for a boat or leisure yacht for up to seven DC circuits. The box provides a negative and a positive bus bar. The bus bars are positioned on top of each other such that the negative and positive terminal for each circuit are aligned vertically. The positive side provides holders for seven MIDI/ANL/DIN 72581-2 fuses or (via an adapter) MINI/ATO/ISO 8820-3 (aka “car”) fuses. The negative bus bar provides an eighth terminal to connect a PE wire, i.e. the distribution box is supposed to be used in negative-grounded DC installations.

Advantages over COTS (commercial-off-the-shelf) Alternatives

  • Space efficiency: That was the main reason why I created the model. I only had 140mm of total space and needed to squeeze the box there. Making my own box allowed me to make the slots for each circuit as wide as necessary for the wire gauge but as small as possible at the same time.
  • Quality-price ratio: This box is designed to house 12mm×4mm = 36mm² copper bus bars which are fine for high-current applications. (Keep in mind that 12V applications require high currents and LiFePO4 batteries can deliver several 100A.) COTS products with a comparable-sized bus bar cost a lot or one gets boxes with bus “bars” which are made from a thin steel sheet.
  • Alignment of negative and positive wire: Most COTS products are either fuse holders or only a single bus bar which means you need to separate boxes for positive and negative wires. This box keeps both wires together.
  • Extra PE connection: For a negative-grounded DC installation the negative bus bar must be connected to the grounding rod. This box features an extra terminal for the PE connection.

Detailed Description

The model houses two 12mm×4mm copper bus bars and cable lugs between 2.5mm² and 35mm². The cable lugs are fastened to the the bus bar with M5/M6 brass screws and washers. The beds for the bus bar contain recesses for the nuts and washers. The distance between the positive bus bar and the terminal stripes is designed for MIDI/ANL/DIN 72581-2 fuses.

The cut-outs for the cable are closed with lead-in stripes which consists of three pieces: a lower stripe, an middle stripe and an upper stripe. The lead-in stripes provide cable sleeve. The cable can be fastened around the cable with cable ties and hence provide a strain relieve. The diameter of the cable sleeve is designed for silicon-insulated, fine-stranded, single conductor cables, i.e. SIF 1×(2.5/6/10/16/35), acc. to VDE nomenclature.

As you have to cut and drill the copper bus bar and the holes must be rather accurate, the model also contains drilling gauges to help to drill the holes into the raw copper bar. The drilling gauges contain a recess to fasten the copper bar during drilling and house steel sleeves to guide the drill bit.

Unfortunately, I had to squeeze the box into a 140mm space so I had to make each terminal slot as small as possible. If I had have more space, I would have made each slot equally wide irrespective of the cable gauge which would allow for more flexibility in the future. The model is designed in FreeCAD and most dimensions are put into spreadsheets. Hence, you should be able to tweak the model according to your needs.

Printing Material and Necessary Accessories

  • Base enclosure and bridge: Prusament PETG CF Black
  • Cable Lead-In Stripes: Prusament PETG Urban Grey
  • Lid: Prusament PETG Chalky Blue
  • Drilling Gauges: Add:North PC CF HT
    (Note: Drilling copper creates a lot if heat, so you need high-temperature resistant material; this specific filament is rated up to 185°C)
  • Bus bars: 12mm×4mm copper bars
  • Fasteners: M5/M6 brass screws, hex nuts and washers

Tags