Case For BluRolls HBC-300W-24V Power Supply (For CoreBoxx)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Replaces hardwired cabling with Fused Switched IEC in and JX16/4 Out. Multiple mounting options. Far sturdier case.
- Rating
- 5 / 5
- Likes
- 15
- Downloads
- 39
- Makes
- 1
- Views
- 289
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial

The What:
This is a ground up designed complete replacement case for the BluRolls HBC-300W-24V power supply that comes with the CoreBoxx kit.
The Why?
I designed this to address several key points with the case model supplied with the CoreBoxx:
Structural Integrity
The supplied case broke the first time I dropped it from 2' onto carpet. So it needed some beefing up.
Existing Connections
The supplied case was totally hardwired from ac plug to board plugin. As such you would need to unplug it from the wall just to shut it off, and further it would still be attached to CoreBoxx making removing the CoreBoxx to service either the CoreBoxx or the CoreOne way more difficult than it needed to be.
I wanted a real IEC input, with a fuse, and a switch. This was a must have.
I also wanted to be able to easily disconnect the 24V DC power going to the CoreBoxx for ease of servicing without having to squeeze the 4 pin molex through the “slot” on back and manipulate it to get it to plug into the Semi Smart Board.
Cable Lengths
Both the supplied AC cord and the power out cords were woefully short of what's needed. I had prop the supply up on a box behind the CoreOne just to get it to reach both the outlet on my power strip and the Molex connector on the Semi Smart just to get some slack on the molex end to not put undo stress on the connector and the board. By going to an IEC cable on the input I can use whatever length I want, and by having a detachable output cable I can make that any length I need as well.
Mounting
There literally were no mounting options for the stock case, either be it at the table level of the CoreOne, or anywhere along the sides back or top of the CoreBoxx. Ideally I wanted the power switch accessible from the front so in an emergency the off switch would be readily accessible. The need for this became even more apparent when I powered it up (by plugging it in, under the table the CoreOne was on, to an outlet strip on hands and knees) where the board erupted in sparks, flashes and smoke as the buck chip gave up the ghost. An accesible off switch at that point would have been a good thing.
Further I wanted some flexibility with the mounting as I'm not sure exactly where it's going to land for the long term.
THE BOM
You'll need a few items besides the models:
IEC Input - QTY 1

There's a whole bunch of vendors on amazon selling these. Make sure you get the multi wire one vs the 3 wire one, because it'll allow you to choose between an always on or only on when switched on power switch illumination (handy for when things are in the dark, and the multi wire flavor uses a DPDT switch vs a SPST switch. This one came with two, as one can never have enough of these on hand.
https://a.co/d/7YpnvZg
GX16-4 Panel Mount (male) and Connector Plug (female) - QTY 2

Again there's a mess of vendors selling these as well. I've got another project that's going to need a mess of these so I went with this one:
IEC Power Cord - QTY 1
I'm sure you probably have a bunch of these laying around, and if not they're common as dirt.
16/4 Cable - However long you like.
What is important to note here is the max OD of the cable for the GX16 can take is around 8mm. Being as 16/4 SOOJ has a spec 7.2mm, that would be fine, however not all wire MFR's pay much attention to that.
I ordered a roll off Amazon and it came in with a 9.2MM OD due to the cheesy outer “might be PVC but feels like god knows what flavor of rubber that rubs off in chunks between your fingers”. So much for that.
Off to Home Depot with calipers in tow to rectify that one. They at least carry US based UL rating stuff that will meet spec.
3mm x 5 (OD) x 4 (H) x 4.2 (Seat Diam) Heat Set Inserts - QTY 10

These are the same ones that came with the BluRolls kit. I order them by the boatload. Just make sure the ones you use have a 4.2 Diameter at the small end that lands onto the the ledge or you'll need to resize your holes in the model. I like these because you can partially “seat” them into the hole before hitting them with the iron and that makes it way easer to keep them perpendicular to the hole when seating.
I'd post an Amazon link but the vendor I got them from last time off Amazon no longer exists (typical).
22-16AWG 8 MM Crimpable Ring Terminals - QTY 7
TOOLS & OTHER ITEMS:
Soldering iron, solder, heat shrink, crimpers, wire cutters etc.
THE BUILD:
THE MODELS:
These are organized as:
Case (V 1.5)
Lid (V1.4)
Case & Lid Together
Case Separate
Lid Separate
Lid Separate (no logo) - if you don't like it or don't want to mess with the color changes.
I'm supplying these in both STEP and .3mf files along with a full Prusa Slicer .3mf project file.
Parts have Revision stamps on them, and if I update them I'll note the versions of the parts and what changed, as well as if it's a required update and if so what prior versions are compatible to remove all the guesswork endemic with this sort of thing. “Have I got the right one? How would I know”.
BRIMS
These were all built to printed in ASA, and due to the length of the things, serious brims are needed to preclude lifting. They're built into both the case proper and the lid models. If printing in PLA/PETG etc where you don't need brims just matrk the brims as non printing and you'll be good to go.
SUPPORTS
All needed supports are also modeled in, in the form of Support Enforcer objects. You can look at the settings in the PrusaSlicer Project file for how I set up multi - material supports. I tend to use the interface method vs full material supports when doing ASA as PLA doesn't like that kind of bed temp, so the PLA only comes into play at the interface layers. The enforcer objects are all sized to do their job but not stick to anything around them.

You can see where the ASA is acting as supports (light green) and the PLA acting as interface (dark green).
I do them that way all the time and provided my enforcers are properly sized (and these are, as they're modeled in) they'll just pop right off. Again see the setup in the project file (BluRulls HBC-300W-24V Case Lower V1.5 & Lid V1.4 (PS XL Project))

Assembly Notes IEC side:

The cavity is designed to give you enough working room to wire up the terminals from the IEC Input/Switch assembly and still keep the entire enclosure length short enough that when mounted vertically it will stay within the bounds of the CoreBoxx. As a result there's not a ton of spare room to work with but it's really not too bad.
The IEC part comes with pre-termed spade terminals, however to fit well in the space you'll want to shorten the on part jumpers – I cut the end off at 8cm and put a new spade terminal on. As they show up from Amazon the switch is wired so the switch light is on when the switch is on. If you reverse the jumpers and feed the incoming ac to the other side of the DPDT switches poles the switch light will always be on regardless of the switch state if you'd like it to operate that way.

AS SHOWN - SWITCH LIGHT FOLLOWS SWITCH STATE - I.E. ON WHEN SWITCH IS CLOSED.
FOR “ALWAYS ON” SWAP BOTH BLACK LINES AND BOTH RED LINES ON THE SWITCHES TERMINALS.

The IEC input plate is a press snap fit, and I cut the upper and lower to meet both the tab's width and its expected panel depth. It's designed to fit tightly to resist pull out if you trip over the cord.

As a result, don't push it all the way in until you've got all the wiring in place. While you can get it back out it's challenging. You'll need a flat blade screwdriver with a very small diameter handle, and will also need to dismount the power supply to reach the lower tabs. It's easiest if you have a couple of these, and use one for one of the top tabs and another for it's corresponding bottom tab, and use both to get one side partially wiggled out, then move to the other side Side. Note that the tabs on the IEC side of the input plate are narrower than the switch side.

The shortened jumpers made the 3 connections to the input on the supply a lot more manageable.
I shortened the switch out leads as well in order to have them land pretty much dead on:

Assembly Notes GX16-4 side:
The GX16's are WAY easier to solder out of the box. I built up the entire thing externally and then installed it. I used 16AWG to get better current capacity out of the connection (the contacts are rated at 10A). The BluRolls supplied cable is like 18 or maybe even 20AWG and while I don't know the total draw of the board, the heater has to pull a fair bit (my Semi Smart board is fried ATM so I never got to the point of metering out the individual components amperage) and I just felt a whole lot better having a 7.4A capacity wire wise on the output side than 4.6A or 3A.
14AWG would have been ideal as the supply is rated for 300W and 14AWG would have netted 11.8A getting 283W cable wise before thermal heating became an issue, but that would have taken a MUCH bigger connector to be able to handle the AWG diameters at the connector solder end.
Being as BluRolls shipped this with 18 or 20 AWG, if they didn't just completely underspec the wire it's likely a 110W or less draw. Hard to tell as my heater unit came loose in the box, with no label, no notes, and no specs. I did have to straighten a couple of the radiating fins out as it got a little beat up during shipping.

The GX16's panel mount terminals when the plate is installed are aligned vertically. As such I chose to split it up so the both -'s are on the same side, stacked vertically looking down at the connector and both +'s are on the other side to better align with the terminal positions on the supply.
Color code wise I went Red/White for the two +'s and Black/Green for the two -'s. Doesn't really matter provided you're consistent all the way through from the supply panel, the connecting cord to the corresponding panel mount on the CoreBoxx.
I soldered the connector ends on, then heat shrinked those, the crimped on the ring terminals (in this case I'm using heat shrink ring terminals).
This side is even tighter than the IEC side so you dont' want tons of slack on the cable lengths. You need just enough to have the line fold over on itself when the rings are seated on the supply end. It's helpful to see the end result first:

GX16-4 Terminals tied into the 24V outs
Note the “fold over”. If you were looking at this from the side, each conductor takes a horizontally flipped “S” shape path from the connector solder point out, then back towards the GX16 side and reverses again to go to the terminal location on the power supply. That's easiest to test fit prior to soldering to get the length dead on.
Once you've got your lengths figured out you can solder up the connector:

GX16-4 Before heat shrinking the ring terminals.

GX16-4 After heat shrinking the ring terminals.
Installing the GX16:
It's easiest to feed the 4 ring terminals through, stopping just as the insulated end of the rings passes through the opening and having the GX16 angled towards the ground. This will give you enough wiggle room to get the GX16's washer and nut over the 4 ring terminals:

Once you get the washer on, pull a bit more of the cable through so the washer goes past the insulation on the terminals and it'll act as a keeper to hold things in place while you get the nut over the terminals. It can help to twist the ring terminals a bit to get the nut over them:

Once you get the nut over the terminals and past the insulation on them the easiest way to get the nut on the GX16's threads is to stand the assembly up on the table and fully seat the GX16's flange against the case. A little shake will get the washer to where it needs to go and you can finger tighten the nut until it threads. Once it threads tighten it down as much as you can with your fingers (Just to make sure it doesn't come loose prematurely) and then use needle nose pliers to tighten it down as there's not really enough room to get full on wrench on the thing. It should only take about ¾-1 turn past finger tight to fully seat the panel mount GX16.
One seated you can use needle nose pliers at the crimp points on the ring connectors to line them up to screw into place, getting us to where we need to be.

GX16-4 Terminals tied into the 24V outs
Note the “fold over”. If you were looking at this from the side, each conductor takes a horizontally flipped “S” shape path from the connector solder point out, then back towards the GX16 side and reverses again to go to the terminal location on the power supply. That's easiest to test fit prior to soldering.
That's it for the installation. You can put the lid on with spare M3's from the BluRolls kit or use M3x8's of your own. You can optionally use washers if you like but it'll probably be just fine with the M3's.
TESTING:

Plug in the IEC and switch the power on. If you used the default wiring as shown the switch will illuminate, the BluRolls supply will fire up and light up a green led and you should have +24 volts available at both pairs of the GX16's output pins.
Note the GX16's connector shell is not connected to any pin of the GX16, so you won't see anything if metering against the shell of the connector.
MOUNTING:
The back of the case has two sets of keyhole slots which give a lot of differing mounting options:
On back panel, vertical with IEC in on top:

On back panel, vertical with IEC in on bottom:

Either side top with IEC to rear (or front if you flip it)

On either side mounted vertically:

On rear using outer keyholes for more back panel accessibility:

On side horizontally with switch forward facing:

This is likely how I'll mount it, as the switch is always handy and right near the door.
In short, you can put it pretty much anywhere you want just by loosening any center pair of M3's that hold the panels on (I unseated them fully then reseated by about 1 ½ - 2 turns and that was pretty close, and you can fine tune it for a snug fit).
If they arent' reaching, you likely sunk the heatset M3's behind the panel deeper than surface flush. You could either:
Reheat the heatset insert a bit, crank in an M3 (I use 50's for that sort of thing) and carefully pull it back out to flush before it cools down.
- or -
Use a slightly longer M3.
The cable and CoreBoxx GX16 mounting:
This is entirely up to you. You can make your connector cable as long as you'd like. If you need to remote the power supply, you can. If you want to table mount the supply with the keyholes like an outlet strip, you can. If you want to wall mount it with mollies you can. That's the whole point.
As for the CoreBoxx's GX16 panel mount you can:
Drill out the hole and put it anywhere you'd like. It'll take a 16mm bit for that.
You'll be cutting the ring terminals off the BluRolls supplied cable from the original supply and soldering that on to other the GX16's panel mount end. That's one option. You should now have plenty of slack on that cable as it's literally entirely within the CoreBoxx proper.
- OR -
You can fab a printed mount for the connector and cut a hole in one of the panels to mount it (if you don't happen to have a 16mm bit).
- OR -
You can wait a bit for the next piece I roll out which will be a panel for both the GX16 and a second cable to handle everything between the CoreBoxx and the CoreOne via this bad boy:

This will have a back panel mount plate for both this connector and the GX16-4 so you can totally unplug the CoreBoxx with 2 connections for the easiest means of servicing, which was the whole point for me for this entire exercise, as it's a major PITA to unplug all that stuff at the semi smart board just to fix an extruder problem on the CoreOne for example.
I wanted a dirt simple, foolproof, short proof, fire proof solution the hard line cables just did not address.
That's up next.
And I STILL don't have a working Semi Smart board. Sigh….
You can let me know on Sanders's discord if you have any questions or reply to the post here.
Enjoy.