1 / 3
VORON 2.4 NOZZLE WIPER (Bambulab wiping style variant) — image 1
1 / 3

VORON 2.4 NOZZLE WIPER (Bambulab wiping style variant)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

i remixed the wiper made by Long . Left side gantry version

Rating
5 / 5
Likes
7
Downloads
22
Makes
1
Views
370
Reviews
1

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

I made it so its compatible with the parts for the wipe mechanism of the bambulab x1c.

 

  • Gantry Mounted (highly recommended versus the bed mounted version)

    • (4) m3 x 5mm x 4mm heat sets

    • (1) m3 x 8mm SHCS

    • (2) m3 x 12mm SHCS (Gantry Arm to Gantry Extrusion)

    • (2) m3 x 16mm (Gantry Arm to Wiper Frame)

  • (6) 6mm x 3mm magnets 

  • (2) m3 x 8mm BHCS or FHCS (Wiper Arm Cap to Wiper Arm)

  • (1) m3 x 10-12mm bolt (optional, for if you need the arm up-stop. I didn't use this)

  • (1) m3 x 30mm bolts

  • (1) m3 nylock nut

  • m2.5 screw

  • Heatbed Nozzle Wiper - A1 | Bambu Lab EU -winkel

  • Nozzle Wiper | Bambu Lab EU -winkel

  • Superglue

 

Build Instructions

  • Print the STLs in the provided orientation

  • Assemble the [Wiper Arm]

    • cut the nozzle wiper from bambulab to a apropriate lengt acording to the picture.

    • Use two m3 heat sets, two m3x8 bolts (preferrably low profile head), m2.5 screw, and one 6mm x 3mm magnet (no glue required for this magnet since it is in opposition to the [Lower Magnet Mount]).

    • If you need to restrict the upward motion of the arm, then add a m3x10 or 12 up through the hole on the underside of the arm

    • put the wiper holder toghetter with the wiper on the wiper arm  after that close it with the slot

  • Assemble the [Nozzle Wiper Frame]

    • Gantry Mounted

      • Melt in two brass heatsets to the underside of the frame (holes that attach to the [Gantry Mount Arm]

      • Insert a m3 nylock nut into the hexagonal hole

      • Attach the wiper arm with a m3x30 bolt into the nylock nut. Leave this bolt somewhat loose so the arm can move freely.

      • Insert two 6mm x 3mm magnets into the side, noting the orientation so they will attract the [Purge Bucket]

      • cut  the bambu lab a 1 wiper brush to the lengt so it fits in the reserved area

      • after that glue it in place you wil need 2

  • Assemble the [Lower Magnet Mount]

    • Insert a 6mm x 3mm magnet into the angled hole on the upper side of the part (makes sure the orientation opposes the magnet in the [Wiper Arm].

    • Insert a m3x8 up through the hole on the underside of the [Lower Magnet Mount]. This is the arm down stop.

      • Adjust this so that it restricts the wiper arm to just above the level of the nozzle tip. This helps give the nozzle tip a firm wipe.

    • Note there is a hole that will fit a magnet on the underside of this part.  It is not needed in this variation of the nozzle wiper.

    • Glue the [Lower Magnet Mount] to the [Nozzle Wiper Base].

  • Assemble the [Purge Bucket]

    • Insert two 6mm x 3mm magnets into the bucket noting the orientation to attract the two magnets in the [Nozzle Wiper Base] 

 

Tags