1 / 5
Creality Chamber Heater on Core One — image 1
1 / 5

Creality Chamber Heater on Core One

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Adding a missing feature on Core One (plus): a chamber heater

Rating
5 / 5
Likes
31
Downloads
30
Makes
1
Views
768
Reviews
1

Updated at source:

Model information

License
Creative Commons — Attribution

It takes some time until the chamber of a Prusa Core One plus reaches the temperature for printing ASA or CF - even worse when the printer is in a cold environment. 

Inspired by the work of @Cedric_91960 I designed and built an adapter plate for using the Creality Chamber Heater HM-01 on a Core One plus. While designing the adapter plate I had the following principles in mind:

  • No supports: all parts should be printable without using supports

  • Light: reduce to the minimum of material needed (not sure whether I reached this goal or not)

  • Design Language: the device shall fit into the original design of the Prusa Core One plus as close as possible

  • Reduce risk of print failures: prefer smaller parts to print over large ones

Bill of material

The result after 5 rejected designs consists of 9 (!) parts which have to be assembled to one unit. I also used three different materials for production (and I suggest you to follow these recommendations):

  • ASA CF for the load-bearing parts: I used 3DJake ASA CF, grey, for this purpose

  • PC for the parts exposed to heat: the outflow of the heater is 100°C, so use a heat resistent material. I used Extrudr Durapro PC FR V0 (which is quite inflammable too)

  • PETG for the decorative parts (could be also ASA, wouldn't recommend PLA) in orange, I used Extrudr PETG, but any other will do

As a matter of fact, you need some additional parts for the final assembly:

  • 6x M5 Inserts (e.g. Ruthex RX-M5x9.5)

  • 3x M3 Inserts (e.g. Ruthex RX-M3x5.7)

  • 6x Screws M5x14 countersunk, black

  • 6x Screws M3x10 (or 12) countersunk, black (mounting the plates to the Core One)

  • 1x Screw M3x10 (or 12) flat, black (mounting the plate from the inside of the Core One)

  • 2x Screws M3x12 countersunk, black (mounting the heater to the bracket)

  • 3x Screws M3x8 countersunk, black (mounting the Inflow hood and deflector)

  • 7x M3 nuts, black

  • Velcro band for remote control

Printing recommendations

ASA CF Parts
  • Layer height 0.2mm

  • 5 Wall loops

  • 4 Top shell layers

  • 4 Bottom shell layers

  • 15% Rectlinear infill

  • 15mm inner and outer Brim

PC Parts
  • Layer height 0.2mm

  • 7 Wall loops (almost no infill)

  • 10mm inner and outer Brim

PETG Parts
  • Layer height 0.2mm

  • 4 Wall loops

  • 5 Top shell layers

  • 5 Bottom shell layers

  • 15% Gyroid infill

  • 8mm outer Brim

Assembly instructions
  • Print all parts

  • Attach the M3 and M5 inserts

  • Start with the Baseplates left and middle: attach the heat ring and deflector, the two plates stick together now

  • Attach the inflow hood to the right base plate

  • Remove the right plexiglas panel of the Core One Plus, remove all bolts and screws

  • Start mounting the right plate. The screw on the lower right side is a bit tricky as the cables of the motor are on the other side of the cabinet wall. Therefore I inserted the (flat) screw from the inside towards the outside. Not nice, but reducing the risks of squeezing cables significantly.

  • Add the two other plates:

  •  Insert the Creality Heater and attach the brackets and cable cover, attach the remote control to the designated place

Usage

When turned on, the heater blows air with ~100°C into the room. A deflector has been fitted to prevent the warm air from hitting the belt. This deflector is available in three different sizes; I am currently using the largest version. Tests have shown that the deflector is effective, meaning that the warm air is directed forwards and upwards. Below the edge of the deflector, the airflow is minimal.

This protects the belt and pulley, and also ensures that the airflow does not hit the plate where the nozzle deposits the hotter filament.

Once the room temperature is reached, the heater’s fan remains switched on, but the outlet temperature drops. The temperature remained stable even during prolonged operation (15 minutes); the temperature shown on the heater’s display was always within the range of ±2°C of that shown on the printer’s display.

I’ve found it works well to switch on the heater for a few minutes at the start of printing (during the warm-up phase). This reduced the time it took for printing to actually begin. During the actual print, the heat from the build plate was able to maintain the temperature, so I usually switched the heater off.

Tags