1 / 6
Hi-Fi Desktop Speaker Cabinets (Overnight Sensations) — image 1
1 / 6

Hi-Fi Desktop Speaker Cabinets (Overnight Sensations)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Enclosures for a pair of cheap (but great sounding) 2-way Hi-Fi speakers.

Rating
5 / 5
Likes
101
Downloads
478
Makes
1
Views
4,969
Reviews
1

Updated at source:

Model information

Category
Audio
License
Creative Commons — Attribution — Noncommercial

Information on the drivers to use and crossover design/schematics can be found here. 

I have now also designed some angled desktop stands for these speakers, can be found here

 

This enclosure design is based on the work of the legendary Paul Carmody, specifically his wildly popular “Overnight Sensations” design. There is an abundance of easy to find information on this design, the speakers are cheap to build and parts easy to source in Australia.

I wanted to prove to myself that a 3d printed speaker enclosure could sound just as good (if not better!) than a traditional wood enclosure, and I must say I am most pleasantly surprised by the results. The speakers sound really “fun”, with a bright engaging high end and a surprising amount of low end grunt for their size! I really don't think the enclosure being made from plastic has any negative effect on the sound quality, although I don't have any measurements to back up this claim. I personally replaced a set of monitor speakers on my desk that cost 4x more than these speakers cost me to build and much prefer the sound of these.

Each speaker is built by using a strong epoxy to glue both front and rear halves together, this was done to maximize the print accuracy where it matters most (rear port and driver cutouts) and the grooves built into the design make the joining of both parts super easy. 

This project is great for those of us who are terrible working with wood (like me!), but have always wanted to get into DIY audio. These speakers are not only a really fun project but can save you money too, they sound much better than they have any right to!

Print Information:

  • Printed on my stock Prusa MK3S+
  • Front half printed with front facing down onto heat bed.
  • Rear half printed with rear facing down onto heat bed.
  • Printed using PLA+ (normal PLA/PETG should also be fine)
  • 6x outer perimeters or more recommended.
  • 70% infill recommended (don't use lower than 40%)
  • Use supports for the enclosure edges, ports on the rear and driver cutouts on front face.
  • Be prepared to do some light post processing of the prints to clean them up!
  • Be careful when printing the front sections, since the tweeter is offset there is a separate STL file for each the front left and front right speaker.
  • Keep an eye out for any warping/lifting early on in the print. If you see any corners lifting I would advise dialing in print settings and trying again. One of my speakers warped slightly when printing (approx. 1mm out of spec) and I still managed to snap the two halves together easily.

Build Information:

  • I used metal threaded inserts to mount the drivers (melted in using soldering iron)
  • Used strong 2-part epoxy to connect both sides of enclosure.
  • Sanded back using 240 grit sandpaper, then with 600/1200 grit after using spray on filler primer. I found the PLA+ I used handled short burst of an electric orbital sander without any issues, just keep feeling the surface for heat build up just to be safe.  
  • The rounded edges of the enclosure can be treated with some gap filler if there is any inconsistencies in the print due to supports etc. I recommend using a filler that is not too thick and one that is easy to sand by hand. 
  • The 4x small nubs located on the inside of the rear half can be used to help secure the crossover circuit.
  • Cheap Chinese made chip amplifiers around the 20-50w range are a great match for this project if you would like to keep costs low. 
  • There are 2x options for tweeters recommended for the overnight sensations, this design is based around the “HiVi” brand tweeter.
  • Holes placed in the rear can be used to perfectly align binding posts. I used these holes as a guide for a drill bit, drilling a hole a couple mm smaller than the diameter of my binding posts. After screwing in binding posts as far as they would go, I heated them using a soldering iron to drive them in the rest of the way, being sure to keep them straight while cooling with a pair of pliers.
  • Blu Tack works well to create a seal between the drivers and the enclosure. Roll the Blu Tack into a very thin and long “rope”. This is especially helpful if the supports didn't come off perfectly clean in the driver mounting holes. I opted to use this method rather than use the gaskets that come with the drivers as the gasket included with the woofer didnt seem to seal very well.  

IMPORTANT: When building the crossover circuit the “10 Ohm” resistor must be replaced with a “15 Ohm” resistor. This is due to using the HiVi tweeter rather than the Dayton Audio tweeter. 

Pay close attention when wiring up the tweeter, as it must be connected in reverse polarity (Ground connected to the “+” of the tweeter, which should be marked red on the tweeter)

Tags