1 / 3
IKEA SKADIS Invisible Board Connectors – Straight & T-Joint — image 1
1 / 3

IKEA SKADIS Invisible Board Connectors – Straight & T-Joint

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Connectors for joining IKEA SKÅDIS boards using M3x14 screws and M3 nuts. Strong, removable and no glue needed.

Rating
0 / 5
Likes
13
Downloads
74
Makes
0
Views
256
Reviews
0

Updated at source:

Model information

Category
Organizers
License
Creative Commons — Attribution — Noncommercial — Share Alike

IKEA SKÅDIS Board Connectors – Straight & T-Joint

A simple and strong connector system for joining multiple IKEA SKÅDIS boards together.

The connectors are mechanically secured using M3x14 screws and M3 nuts, so no glue is required. The connection is strong, clean and removable, making it easy to rearrange or expand your SKÅDIS setup.

The set includes connectors for straight board-to-board connections as well as T-joint connections.

Required hardware:

  • M3x14 screws

  • M3 nuts

Print settings:

  • Material: PLA

  • Layer height: 0.2 mm

  • Nozzle: 0.4 mm

  • Supports: Required for the M3 nut slots

Assembly:

  1. Remove the supports from the nut slots after printing.

  2. Press the M3 nuts firmly into the hexagonal slots in the connector.

  3. Make sure the nuts are fully seated.

  4. Place the connector on the back side of the SKÅDIS boards.

  5. Insert the printed washers from the front side.

  6. Insert the M3x14 screws through the washers and SKÅDIS boards into the nuts.

  7. Tighten the screws evenly until the boards are firmly connected.

No glue required.

Do not overtighten the screws to avoid damaging the printed parts or the SKÅDIS boards.

Spojky pro IKEA SKÅDIS – rovné a T spojení

Jednoduchý a pevný systém spojek pro spojování více panelů IKEA SKÅDIS dohromady.

Spojky jsou mechanicky upevněny pomocí šroubů M3x14 a matic M3, takže není potřeba žádné lepidlo. Spojení je pevné, čisté a zároveň rozebíratelné, takže lze sestavu SKÅDIS snadno upravovat nebo rozšiřovat.

Sada obsahuje spojky pro rovné spojení panelů i pro spojení do tvaru T.

Potřebný spojovací materiál:

  • šrouby M3x14

  • matice M3

Nastavení tisku:

  • Materiál: PLA

  • Výška vrstvy: 0,2 mm

  • Tryska: 0,4 mm

  • Podpěry: Nutné pro otvory/lůžka na matice M3

Montáž:

  1. Po vytištění odstraňte podpěry z otvorů pro matice.

  2. Zatlačte matice M3 pevně do připravených šestihranných lůžek ve spojce.

  3. Zkontrolujte, že jsou matice správně a úplně usazené.

  4. Umístěte spojku na zadní stranu panelů SKÅDIS.

  5. Z přední strany vložte vytištěné podložky.

  6. Protáhněte šrouby M3x14 skrz podložky a panel SKÅDIS do matic ve spojce.

  7. Šrouby rovnoměrně dotáhněte, dokud nejsou panely pevně spojeny.

Není potřeba žádné lepidlo.

Šrouby nedotahujte příliš silně, aby nedošlo k poškození vytištěných dílů nebo panelů SKÅDIS.

Tags