1 / 3
Centauri-Monitor - ESP32 Elegoo CC1 status monitor — image 1
1 / 3

Centauri-Monitor - ESP32 Elegoo CC1 status monitor

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A 3D print monitor for Elegoo Centauri Carbon printer(CC1), running on an ESP32-C3 with an OLED display and a web-based

Rating
5 / 5
Likes
5
Downloads
24
Makes
1
Views
255
Reviews
1

Updated at source:

Model information

Category
Accessories
License
Creative Commons — Attribution — Noncommercial

Centauri-Monitor - ESP32 Elegoo CC1 status monitor


A 3D print monitor for Elegoo Centauri Carbon printer(CC1), running on an ESP32-C3 with an OLED display and a web-based configuration panel.
 

Features

  • Reads printer status via the SDCP protocol (WebSocket, port 3030): state, progress, elapsed/remaining time, nozzle/bed/chamber temperatures, layers.

  • OLED display 128×64 (I2C) with animated screens: printing, paused, complete, idle, WiFi setup (AP mode), connecting. visualization here: https://github.com/osait98/centauri-monitor/tree/master/docs/screens

  • Web panel (served directly from the ESP32) for:

    • WiFi configuration (network scan or manual SSID entry),

    • setting the printer's IP address, poll interval, and OLED rotation,

    • viewing the current print status,

    • factory reset.

  • Automatic fallback to AP mode (ElegooMonitor / elegoo123, 192.168.4.1) when no network is saved or the connection fails.

  • mDNS: the panel is reachable at http://elegoo-monitor.local.

  • Configuration is stored in flash (NVS/Preferences) — survives restarts and power loss.

 

Printing

Before printing, measure the width and height of your OLED display. Standard displays are usually around 26 mm. If your display is around 26 mm, use the files from the centauri-monitor-26mm-display directory.

If your display is larger and closer to 27 mm or more, use the files from the centauri-monitor-27mm-display directory.

Hardware

  • ESP32-C3-supermini or ESP32-C3-zero

  • SSD1306 0,96" OLED display, 128×64, I2C, address 0x3C

Wiring

  • OLED → ESP32

    • SDA → GPIO10

    • SCL → GPIO9

    • VCC → 3V3

    • GND → GND

 

Assembly Guide

  1. Connect OLED display with ESP with 4 wires according to Wiring

  2. Place the ESP32 inside the main body in the designated spot. It should gently click into place when pressed in and sit securely and firmly without moving.

  3. Place the OLED display inside the main body. The OLED screen should sit roughly in the center. The cover will center and hold it in place.

  4. Slide the cover into place.

Flashing Firmware

Follow instruction from github https://github.com/osait98/centauri-monitor/releases

 

First boot — WiFi setup

  1. Power on the device. OLED shows SETUP MODE.

  2. Connect your phone/PC to WiFi network ElegooMonitor, password elegoo123.

  3. Open http://192.168.4.1 in your browser.

  4. Select your network → enter password → Save & Connect. Device restarts. The ESP32-C3 only works on 2.4 GHz WiFi networks.

  5. After reboot open http://<ESP IP> — shown in the status bar at the bottom of the panel

  6. Go to the Settings tab → enter your Elegoo printer IP → Save.

Tags