1 / 1
DUAL WHISTLE (D DRONE + D PENTATONIC MELODY) V1.1 — image 1

DUAL WHISTLE (D DRONE + D PENTATONIC MELODY) V1.1

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

3D-printed dual whistle: a single fused mouthpiece with a Y-forked mouth-hole feeding two completely separate airways.

Rating
0 / 5
Likes
0
Downloads
6
Makes
0
Views
66
Reviews
0

Updated at source:

Model information

Category
Music
License
Creative Commons — Attribution — Noncommercial — Share Alike

DUAL WHISTLE (D DRONE + D PENTATONIC MELODY)

==============================================

3D-printed dual whistle: a single fused mouthpiece with a Y-forked

mouth-hole feeding two completely separate airways, splitting into a

plain drone body and a 4-hole pentatonic melody body. One breath plays

both simultaneously.

PARTS LIST / FILES TO PRINT

----------------------------

1x UnifiedMouthpiece_YFork.stl -- the moutpiece

2x Piece1_lib.stl -- plain body section, IDENTICAL

part used on both the melody

side and the drone side

1x HighD_Body_Piece2_pentatonic_enlarged20.stl

-- melody body: 4 holes (D major

pentatonic), enlarged 20% over

the original hole size

1x Piece2_NoHoles.stl -- drone body: plain, no holes

1x FigureEightClip_Piece1.stl -- split-ring clip that holds the

two Piece1 bodies together

Each Piece1_lib.stl print is identical -- there is no left/right

version, just print two.

PRINT ORIENTATION

------------------

Not independently re-verified for this specific mouthpiece shape --

carry over the "diagonal, holes-up" convention used on the earlier

single-whistle mouthpieces in this project as a starting point, but

check for yourself before committing to a full print run, especially

around the Y-fork throat and the septum wedge inside it.

ASSEMBLY ORDER

---------------

1. Print all parts listed above.

2. Check the labium edge on the mouthpiece. A slightly blunt edge

straight off the printer is normal for FDM and usually needs a

light touch-up with a small file to get the whistle to speak

cleanly -- this is expected, not a sign anything printed wrong.

3. Identify which mouthpiece socket is which:

- one socket feeds the melody (pentatonic) side

- the other feeds the drone side

Dry-fit before gluing/taping anything to confirm orientation.

4. Push a Piece1 body into each of the mouthpiece's two sockets

(melody side and drone side).

5. Seal both joints. The tenon/socket fit is dimensioned tight but is

not airtight straight off the printer -- wrap with tape (PTFE

plumber's tape or similar) or use a bit of wax/glue at the joint,

the same way traditional wooden whistle joints are sealed. Reseal

as needed if it starts leaking air during play.

6. Slide the figure-8 clip onto the two Piece1 bodies. The clip has a

split in each ring so it flexes open and snaps on rather than

needing to slide over a free end. It sits against the socket

collars, roughly in the middle of Piece1's plain section --

clear of both the mouthpiece joint above and the Piece2 joint

below.

7. Push the pentatonic Piece2 into the melody-side Piece1, and the

no-holes Piece2 into the drone-side Piece1.

8. Seal these two joints the same way as step 5.

9. Test blow. See notes below on what to expect.

WHAT TO EXPECT / KNOWN CHARACTERISTICS

----------------------------------------

- Volume is on the quiet side even after widening the windway to match

the louder Bb13 mouthpiece design. Good for solo/quiet playing, may

get lost next to other instruments. If more volume is wanted later,

the windway HEIGHT (currently 1.15mm, unchanged through this whole

project) is the next lever to try, along with checking whether the

Y-fork throat itself is adding flow resistance the single-whistle

design didn't have.

- Pentatonic melody side was chosen deliberately over the original

6-hole major scale specifically because it's paired with a fixed

drone note -- the major scale's 4th and 7th degrees (which the

pentatonic omits) tend to clash against a sustained drone tone.

- Joints need active sealing (tape/wax) to hold air -- this is a

normal property of FDM-printed tenon/socket joints at this scale,

not a fit defect.

FILE HISTORY NOTE

-------------------

This project went through many mouthpiece design iterations (a

strut-bridged twin-mouthpiece version, a nose-extension version, an

early flat-hulled Y-fork with an oversized opening) before arriving at

UnifiedMouthpiece_YFork

Version 1.1: Flattened windway floor to see if can increase volume.

## License

CC BY-NC-SA -- attribution required, non-commercial use only,

derivatives must stay open under the same terms.

## Credits

Design, testing, and all the physical building/iteration by me.

OpenSCAD source developed with the help of Claude (Anthropic).

Tags