Centuari Carbon 1 Canvas Magnetic LED Toolhead - Skeleton Remix
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This is a magnetic CC1 Canvas - Skeleton LED toolhead remix from PROUTING & Duckferd toolheads. Fits the CC1 fan.
- Rating
- 0 / 5
- Likes
- 17
- Downloads
- 55
- Makes
- 0
- Views
- 508
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a magnetic CC1 Canvas - Skeleton toolhead remix from PROUTING & Duckferd toolheads. Fits the CC1 fan. I couldn't find what i wanted so i made it. Prouting hasn't added a Skeleton Canvas Magnet so I made it and added LED option from Duckferd because it looked cool. Its also useable without adding an led. Its a major pain in the butt to unscrew the original cover to adjust filament tension, change, and unclog nozzles. This also addresses the annoying buzzing vibrating sounds the original toolhead cover can make. Often misdiagnosed by Elegoo as dry bearings. The magnets are 5mm x 10mm for cover and 3mm x 6mm for detachment sensor (because that's what I had). The front works with any of Proutings magnetic back covers. This cover reduces vfa's and seems to generally print better than the original Elegoo cover. I've uploaded a .step file so you can modify easier as you like.
***copied from duckfords remix***
LED questions please refer to his remix. I haven't added LED's to mine yet. I made this first thinking it would work with the CC2 without realizing it was a different fan. doughhhh. I also uploaded a CC2 specific remix.
This is a remix of Prouting's Magnetic Skeletonized Centauri Carbon Toolhead, specifically the front cover with a pocket modelled in to allow the use of a FYSETC 24V LED. Duckferd purposely made the fit a bit loose as you may be using an uncalibrated shrink-prone material like ABS or ASA, but you can just use a bit of superglue or epoxy to hold the LED in place.
The FYSETC LED is dimensionally similar to the ubiquitous Neopixels used in DIY 3D printer setups so you have flexibility to use similar formfactor LEDs, just be mindful of voltage requirements and whether a converter is required.
Duckferd also uploaded an updated version of the magnetic skeletonized backplate that has revised hole spacing (1mm inboard for all 3), which corrects screwhole spacing issues at least on his Centauri Carbon.
In order to complete this mod, you have to match the positive/neutral wires from the LED harness to the positive and negative on the toolhead fan. In other words- match red wire to red wire; black wire to black wire.
There are a couple of ways of doing this- either splice it directly to the fan side wiring itself (cheapest and simplest, irreversible but at least the fan is replaceable so not a big deal), or like him you create a 4pin male-female JST-ZH (get the M-F 4pin set, length doesn't really matter since you only need a few cm) adapter to go between the fan and toolhead and splice power from that to the LED. Even better if you can get your hands on a terminal and connector kit to crimp your own from scratch.
The adapter Duckferd made below he spliced just the positive and negative 24V to the LED leaving the tach and fan control as pass-through. He elected to solder and heat shrink this assembly. The one thing he did notice with the Aliexpress JST listing is that the color order of the wires are reversed. He repinned the connectors to the right order, but if you're confident you won't make a mistake, it doesn't really matter. He finished this with a short length of cable sleeving just to keep things manageable and slightly better to look at.


Then you just plug everything together and the LED will light up as the printer comes online.