Spider-Man Desk Buddy — Monitor & Shelf Sitter
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
He sits on the edge of your monitor and waves at you all day.
- Rating
- 0 / 5
- Likes
- 4
- Downloads
- 43
- Makes
- 0
- Views
- 156
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Office
- License
- Standard Digital File License
He sits on the edge of your monitor and waves at you all day.
A chibi Spider-Man desk buddy — a 100 mm sitting figure with the legs left to dangle, so he perches
on the top edge of a monitor, a shelf, a bookcase or the lip of your desk. One hand is up in a
wave, the other rests flat beside him, and the whole suit is cut with the web pattern right down to
the soles of the boots. No magnets, no glue, no counterweight: the dangling legs brace against the
front of the ledge and hold him there.
Why you will like him
- Made for an edge — the seat sits 51 mm above the toes, so the legs hang clear of a monitor bezel
or a shelf front instead of resting on it.
- Single part — one watertight STL, no assembly, no hardware. Print it, clean the supports, done.
- Reads at a glance — the web lines are cut deep enough to show up even in plain grey or white
filament, with no painting and no AMS.
- Great AMS/MMU project too — the mask, the body web and the eye lenses are separate enough to
paint in red / blue / white if you have multi-colour.
- Prints on any bed — a 64 × 66 mm footprint, so it fits an A1 mini or a Mini+ with room to spare.
- Perfect small gift — a few hours of print time and one spool colour, and it lands better than
most things twice the size.
Where he sits
Monitor top bezel · shelf and bookcase edges · the front lip of a desk · a stack of books · the top
of a PC case · a plant pot rim. He is deliberately front-heavy, so he needs an edge to lean into —
he will not stand up in the middle of a flat table, and that is by design.
Print settings
- Layer height: 0.2 mm (0.12–0.16 mm if you want the web lines razor sharp on the mask)
- Nozzle: 0.4 mm — 0.2 mm is even crisper on the eye lenses, 0.6 mm loses the finest web strands
- Supports: yes — tree / organic, painted or automatic. The raised waving hand, the underside of
the mask and the outstretched palm are the three spots that need them. Roughly 14 % of the surface
sits past 45°.
- Orientation: print him upright, in the sitting pose. The bed contact is only the toe tips, so the
slicer will build a support tower under him — that is normal, and it keeps the whole front face
untouched.
- Walls: 3 · Infill: 10–15 % gyroid — he is decorative, there is nothing to gain from filling him
- Material: PLA, and matte PLA is the pick — it kills the shine, and the web lines read far better
than on glossy or silk
- Time and filament: about 6–8 hours and 30–40 g at 0.2 mm with 15 % infill, plus support
Size
64 mm wide × 66 mm deep × 100 mm tall. Seat height 51 mm above the toes — that is the drop the legs
need in front of the ledge. Scale him to 70 % for a small shelf and he still holds together; above
150 % the head starts to want more than tree supports can comfortably carry.
Tips
- Slow the outer wall down over the mask. The web lines are shallow grooves and they smear at high
wall speeds.
- Take the supports off the mask last, and take them off warm, straight after the print — cold PLA
chips at the edge of the eye lenses.
- A single pass of a grey or black wash into the web grooves, wiped back with a cloth, turns a
plain print into a display piece in ten minutes.
- On a very thin monitor bezel, press him back until the calves touch the front of the panel — that
is what stops him rocking.
- Red PLA for the mask and boots, blue for the body: if you have an AMS, this is a two-colour
print, not a four-colour one.
Found it useful?
A like, a boost or a make with a photo genuinely helps — and I read every comment, so tell me which
character should get the desk-buddy treatment next.
Fan art, made by a fan. Spider-Man and all related characters are trademarks of Marvel Characters,
Inc. / The Walt Disney Company. This model is not affiliated with or endorsed by them and is shared
for personal, non-commercial printing only.
