1 / 2
Spider-Man Desk Buddy — Monitor & Shelf Sitter — zdjęcie 1
1 / 2

Spider-Man Desk Buddy — Monitor & Shelf Sitter

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

He sits on the edge of your monitor and waves at you all day.

Ocena
0 / 5
Polubienia
4
Pobrania
43
Wydruki
0
Wyświetlenia
156
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Office
Licencja
Standard Digital File License

He sits on the edge of your monitor and waves at you all day.

A chibi Spider-Man desk buddy — a 100 mm sitting figure with the legs left to dangle, so he perches

on the top edge of a monitor, a shelf, a bookcase or the lip of your desk. One hand is up in a

wave, the other rests flat beside him, and the whole suit is cut with the web pattern right down to

the soles of the boots. No magnets, no glue, no counterweight: the dangling legs brace against the

front of the ledge and hold him there.

Why you will like him

- Made for an edge — the seat sits 51 mm above the toes, so the legs hang clear of a monitor bezel

or a shelf front instead of resting on it.

- Single part — one watertight STL, no assembly, no hardware. Print it, clean the supports, done.

- Reads at a glance — the web lines are cut deep enough to show up even in plain grey or white

filament, with no painting and no AMS.

- Great AMS/MMU project too — the mask, the body web and the eye lenses are separate enough to

paint in red / blue / white if you have multi-colour.

- Prints on any bed — a 64 × 66 mm footprint, so it fits an A1 mini or a Mini+ with room to spare.

- Perfect small gift — a few hours of print time and one spool colour, and it lands better than

most things twice the size.

Where he sits

Monitor top bezel · shelf and bookcase edges · the front lip of a desk · a stack of books · the top

of a PC case · a plant pot rim. He is deliberately front-heavy, so he needs an edge to lean into —

he will not stand up in the middle of a flat table, and that is by design.

Print settings

- Layer height: 0.2 mm (0.12–0.16 mm if you want the web lines razor sharp on the mask)

- Nozzle: 0.4 mm — 0.2 mm is even crisper on the eye lenses, 0.6 mm loses the finest web strands

- Supports: yes — tree / organic, painted or automatic. The raised waving hand, the underside of

the mask and the outstretched palm are the three spots that need them. Roughly 14 % of the surface

sits past 45°.

- Orientation: print him upright, in the sitting pose. The bed contact is only the toe tips, so the

slicer will build a support tower under him — that is normal, and it keeps the whole front face

untouched.

- Walls: 3 · Infill: 10–15 % gyroid — he is decorative, there is nothing to gain from filling him

- Material: PLA, and matte PLA is the pick — it kills the shine, and the web lines read far better

than on glossy or silk

- Time and filament: about 6–8 hours and 30–40 g at 0.2 mm with 15 % infill, plus support

Size

64 mm wide × 66 mm deep × 100 mm tall. Seat height 51 mm above the toes — that is the drop the legs

need in front of the ledge. Scale him to 70 % for a small shelf and he still holds together; above

150 % the head starts to want more than tree supports can comfortably carry.

Tips

- Slow the outer wall down over the mask. The web lines are shallow grooves and they smear at high

wall speeds.

- Take the supports off the mask last, and take them off warm, straight after the print — cold PLA

chips at the edge of the eye lenses.

- A single pass of a grey or black wash into the web grooves, wiped back with a cloth, turns a

plain print into a display piece in ten minutes.

- On a very thin monitor bezel, press him back until the calves touch the front of the panel — that

is what stops him rocking.

- Red PLA for the mask and boots, blue for the body: if you have an AMS, this is a two-colour

print, not a four-colour one.

Found it useful?

A like, a boost or a make with a photo genuinely helps — and I read every comment, so tell me which

character should get the desk-buddy treatment next.

Fan art, made by a fan. Spider-Man and all related characters are trademarks of Marvel Characters,

Inc. / The Walt Disney Company. This model is not affiliated with or endorsed by them and is shared

for personal, non-commercial printing only.

Tagi