1 / 9
Honey Gate Valve / Squeeze Tap for Honey & Thick Liquids – No Supports // Quetschhahn Honig & dickflüssige Medien – kein Support — image 1
1 / 9

Honey Gate Valve / Squeeze Tap for Honey & Thick Liquids – No Supports // Quetschhahn Honig & dickflüssige Medien – kein Support

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Quetschhahn ist die 3D-druckbare Nachkonstruktion eines Original-Abfüllhahns.

Rating
0 / 5
Likes
3
Downloads
28
Makes
0
Views
82
Reviews
0

Updated at source:

Model information

Category
Other Ideas
License
Creative Commons — Attribution — Noncommercial

## About this model

This is a 3D-printable redesign of an original honey gate valve, the kind used by beekeepers to tap honey from buckets and containers. I fully re-modeled the original part and reworked several areas specifically so that every part prints without support structures – critical areas were reinforced to keep it strong.

Besides honey, this gate valve works well for any thick liquid — syrup, jam, oil or similar media.

⚠ Material note (food contact): PLA is recommended, since it prints most reliably and dimensionally accurate without supports. PLA is not certified as food-safe !

## Parts list

Printed parts (1 set = 3 parts, print time ~1h 50min):

- 1× Valve body

- 1× Cap

- 1× Lock nut

Hardware (not printed):

- 2× M6 × 25mm screw

- 1× M6 nut

- 1× M6 wing nut

- 2× O-ring 43 × 3mm

## Print settings

| Setting | Value |

|---|---|

| Material | PLA (see note above) |

| Nozzle | 0.4mm |

| Layer height | 0.15mm (for best results) |

| Supports | None – deliberately designed support-free |

| Infill |  15% - feel free to increase the vertical contour envelope to a perimeter of 3–4 ;)

| Print time | ~1h 50min per set (3 parts) |

## Assembly

1. Seat one O-ring on the sealing surface of the valve body (funnel piece) and insert it from the inside through the hole in the bucket/bucket lid.

2. Slide the second O-ring onto the valve body's thread from the outside.

3. Thread the lock nut onto the valve body from the outside and hand-tighten until the valve body is firmly and tightly seated against the bucket wall.

4. Attach the cap (with its molded flip lever) on one side of the funnel opening using one M6×25 screw as a pivot, and secure it with the M6 nut — the cap now swings open and closed around this axis.

5. Mount the second M6×25 screw on the opposite side and fit the wing nut. This acts as a tool-free latch: close the cap, hand-tighten the wing nut to hold it shut, and loosen it again to open.

6. Before first use, check that the hinge moves smoothly and that the O-rings seal properly (e.g. test with water before filling with honey).

Feel free to post a Make! 🐝I'd love to see it!

## Über dieses Modell

Dieser Quetschhahn ist die 3D-druckbare Nachkonstruktion eines Original-Abfüllhahns, wie er in der Imkerei zum Abfüllen von Honig aus Eimern und Behältern verwendet wird. Ich habe das Original vollständig nachgezeichnet und an mehreren Stellen gezielt umkonstruiert, damit sich alle Teile ohne Stützstrukturen drucken lassen – kritische Bereiche wurden dafür verstärkt.

Neben Honig eignet sich der Hahn für alle dickflüssigen Medien, z. B. Sirup, Marmelade oder ähnliche Flüssigkeiten.

⚠ Hinweis zum Material (Lebensmittelkontakt): Empfohlen wird PLA, da es sich am zuverlässigsten und maßgenauesten ohne Support drucken lässt. PLA ist nicht als lebensmittelecht zertifiziert.

## Teileliste

Druckteile (1 Satz = 3 Teile, Druckzeit ca. 1 h 50 min):

- 1× Hahn

- 1× Deckel

- 1× Kontermutter

Zubehör (nicht gedruckt):

- 2× Schraube M6 × 25 mm

- 1× Mutter M6

- 1× Flügelmutter M6

- 2× O-Ring 43 × 3 mm

## Druckeinstellungen

| Parameter | Wert |

|---|---|

| Material | PLA (siehe Hinweis oben) |

| Düse | 0,4 mm |

| Layerhöhe | 0,15 mm (für beste Ergebnisse) |

| Support | Nein – bewusst supportfrei konstruiert |

| Fülldichte | gerne die vertikale Konturhülle auf Perimeter 3-4 erhöhen ;) |

| Druckzeit | ca. 1 h 50 min pro Satz (3 Teile) |

## Montage

1. Einen O-Ring auf die Dichtfläche des Hahns (Trichterkörper) auflegen und den Hahn von innen durch die Bohrung in Eimer bzw. Eimerdeckel stecken.

2. Den zweiten O-Ring von außen auf das Gewinde des Hahns schieben.

3. Die Kontermutter von außen auf das Gewinde des Hahns schrauben und handfest anziehen, bis Hahn und Eimerwand fest und dicht miteinander verbunden sind.

4. Den Deckel (mit angeformtem Klapp-Hebel) mit einer M6×25-Schraube als Drehachse an einer Seite der Trichteröffnung befestigen und mit der M6-Mutter kontern – der Deckel lässt sich nun um diese Achse auf- und zuklappen.

5. Die zweite M6×25-Schraube auf der gegenüberliegenden Seite montieren und die Flügelmutter aufsetzen. Sie dient als werkzeuglose Verriegelung: Deckel zuklappen, Flügelmutter handfest andrehen, um ihn geschlossen zu halten – zum Öffnen einfach wieder lösen.

6. Vor dem ersten Einsatz die Leichtgängigkeit des Klapp-Mechanismus und die Dichtigkeit der O-Ringe prüfen (z. B. mit Wasser testen, bevor Honig eingefüllt wird).

## Für wen ist das?

Für alle die dickflüssige Medien umfüllen müssen...

Verbesserungsvorschläge oder ein Foto deines Drucks? Immer her damit – ich freue mich über jeden „Make“! 🐝

Tags