GT2 Belt Tension Meter with Magnetic Spring.
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Highly sensitive GT2 belt tension meter with magnetic spring and DVD-ROM shafts.
- Rating
- 0 / 5
- Likes
- 34
- Downloads
- 35
- Makes
- 0
- Views
- 664
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Accessories
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
⚠ Attention! The accuracy of this belt tension meter depends on the precision of its manufacturing. Your printer must be well-calibrated, and shrinkage tests for the filament should be performed. Holes printed perpendicular to the bed are set to 3.2 mm in the STL files instead of 3 mm to compensate, therefore the slicer’s hole compensation function must be disabled.
Parts shown in red (in the image) are recommended to be printed in ABS/ASA, while the grey parts should be printed in PETG. The part named “detent” is best printed in nylon.
The construction uses 3 mm shafts from DVD-ROM drives — they are highly precise and polished. Other options may exist, but I chose these. After printing, the shaft holes must be calibrated with a 3 mm drill bit, and the detent part should move freely along the shafts.
A piece of GT2 belt about 22 mm long (slightly worn belt is better) is glued to the detent part with cyanoacrylate adhesive (two-component glue is preferable). For good adhesion, the belt should be sanded with fine sandpaper and cleaned with acetone. After gluing, rub the belt with a graphite pencil for lubrication.
A 20-tooth timing pulley (used one is better) with a 5–26 mm shaft piece is pressed against the belt by a lever with backlash adjustment. Adjust so that there is no play, but the detent part can slide down the shafts under its own weight (without magnets) when the meter is turned vertically.
During assembly, lubricate the specified points with light oil (see image). Bearings should be washed in gasoline and left unlubricated.
Calibration must be performed as described here: https://github.com/Diyshift/3D-Printer/tree/main/GT2%20Belt%20Tension%20Meter For loading, a water bottle is convenient. During calibration, adjust the screw that sets the magnet position so that the front of the detent aligns with the “reference position” mark (see image).
The pointer tip is made from a 0.5 mm pin needle, painted black for visibility. The scale is printed on a laser printer on plain paper and laminated with transparent tape.
A well-assembled meter reacts to belt tension changes within 10–15 grams (about a quarter turn of an M3 screw). Verification was performed with a strain gauge meter.
Parts Required for Assembly
Magnets 15×5 mm – 2 pcs
Self‑tapping screws 1.6–1.9 mm × 8 mm – 4 pcs
M2.5 screws × 10 mm – 4 pcs
M3 screws × 12 mm – 2 pcs
M3 screw × 25 mm – 1 pc
M4 screw × 20 mm – 1 pc (preferably stainless non‑magnetic steel)
M2 screws × 10 mm – 2 pcs
Washers 8 mm outer / 3 mm inner / 0.5 mm thick – 2 pcs
Spring: 4 mm outer / wire 0.8 mm – 1 pc
DVD shafts 3 mm – 2–3 pcs (any other 3 mm shaft can be used for the lever mount)
Timing Pulley 20‑tooth with 5 mm shaft, length 26 mm – 1 pc
Bearings 9 mm outer / 5 mm inner / 3 mm thick – 2 pcs
Bearings 9 mm outer / 4 mm inner / 4 mm thick – 2 pcs
Shaft 4 mm × 15 mm – 1 pc
Brass heat‑set inserts:
M3 – 3 pcs
M2 – 2 pcs
M2.5 – 4 pcs
M4 – 1 pc
Steel or nylon shims:
5 mm outer / 3 mm inner / 0.2 mm thick – 2 pcs (for both sides of the lever axis)
6.5 mm outer / 5 mm inner / 0.2 mm thick – 2 pcs (for both sides of the timing pulley axis)