1 / 4
BC250 Case MKUU+ (FSP, Apevia, Metalfish PSU) — image 1
1 / 4

BC250 Case MKUU+ (FSP, Apevia, Metalfish PSU)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Case for BC250

Rating
0 / 5
Likes
20
Downloads
131
Makes
0
Views
1,189
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

This is a remix based off the work created by the very talented morph91. This remix project would have not been possible without his incredible original model! This remix is a large overhaul of almost everything from the original model - with various modifications, additions, and enhancements. I've spent over a hundred hours and printed dozens of prototypes to bring this remix to life. Which is why I decided to name this a "plus" version : )

 

Case Highlights:

Easy to print

  • The entire case can be printed in as little as 3 plates with less than 600g of filament used! Print time without the optional parts is about 20 hours total.

Easy setup

  • This case can be used with 0 modifications to the stock heatsink (no messing with the fins required). However, for best performance some easy to do modifications are highly recommended (see more in the Assembly Instructions section and Comparison of all Thermal Improvement Mods section).

Easy to assemble

  • The entire case can be assembled or dissembled in a couple minutes. It's also a hardware free design, that does not require you to purchase any screws/magnets/heat inserts/tools.

Wide compatibility

  • Dedicated profiles that fit the three most popular flex PSUs for the BC250 (FSP500-30AS, Apevia ITX Flex, and Metalfish Flex). Expanded compatibility to all flex PSUs, via this remix thanks to jinson.

  • This model can be printed on smaller 3d printers using the A1 mini profile.

Wide customization

  • Upper and lower front plates allow you to change the look of your case. Rear side has mounting points for 40 & 50mm fans. Different fan shrouds allowing you to choose between standard 25mm thick fan or 30mm thick fans. Also created customizable IO shield.

Improved thermals compared to original model

  • With slight modifications to the stock heatsink (adding stick on heatsinks and straightening only a small amount of the stock heatsink fins) - thermals improve significantly. This is mostly thanks to the new fan shroud I created that directs airflow in 3 ways: to the stock heatsink, to the stick on heatsinks, and to the backplate. I also created two sizes of shroud extenders that help direct the stick on heatsink airflow to the rear of the case (though they mostly serve to protect your fingers/cables from the stick on heatsink).

Improved usability compared to original model

  • I created an internal clip system that helps hold both sides of the case together more securely. As an optional print plate, I created a front half of the case that has an integrated usb hub. Also, I changed the external psu lock to an internal one instead. Which completely eliminates the issue from the original case, where repeat usage would snap the tab.

  • I created two different fan grills that attach flush to the case to help prevent accidental finger/paw pokes. These grills were designed to have as minimal fan turbulence as possible. Also, the right side of case was redesigned to prevent accidental touches to the backplate. Helping prevent children/pets from accidental burns.

  • Fixed fan centering. Fixed fan shroud sliding/wiggle issue.
     

Important Notes:

  1. There are multiple different versions of the fan shroud. Please print only one fan shroud plate, that is applicable to your use case. If you are not planning on doing the heatsink modifications like I did (stick on heatsinks and straightening fins) - then choose one of the "original" fan shroud plates. If you are planning on using stick on heatsinks, then choose one of the "heatsink" fan shroud plates. If you are using a standard thickness 120mm fan, then only print one of the plates that say 25mm! If you are using a 30mm thick 120mm fan (5 mm thicker than standard), then only print one of the plates that say 30mm! The shroud extenders are only meant for the heatsink fan shroud models.

     

  2. There are two versions of the front half of the case. If you want a front usb hub, then print that version. If you don't plan on having a front usb hub, print the version without one. Same goes with the cover plate.

     

  3. The internal psu lock for the Metalfish version has yet to be confirmed whether it fits. The Apevia one should fit, but I used someone's 3d model of the Apevia psu to test fitment. I did my best approximations with the measurements/models I could find online, but I would like to have confirmation of fitment from a real life test. If they do not fit, please let me know and if you can test some prototypes I will have them fixed ASAP. If you rather just use something that screws the Apevia/Metalfish PSUs in place instead of the internal locks then print this remix, credit to jinson.

     

  4. I am not planning to remix the dual fan version. This is due to this study, that shows 0 improvement in thermals between single and dual fans. If anything, it showed dual fans are detrimental thanks to the increased noise by +5 to +9dBA compared to a single fan. Based on that study, I chose to increase heatsink surface area with stick on heatsinks - which resulted in actual thermal improvements.

     

  5. A high static pressure 120mm fan with good airflow is required! Most regular pc case fans will not provide enough pressure/airflow for cooling. The arctic p12 pro pst is a great budget choice.

     

  6. Heatsink modifications while technically optional, are highly recommended to do to get the best performance out of this case.

     

  7. The A1 mini profile contains all the models from all the different versions combined into one. Please pay attention to the name of print plates to determine what you actually want to print.

 

My Part List:

Required:

Optional:

 

Print Instructions:

Please read the "Important Notes" section very carefully! If you do not you may end up printing incompatible parts.

I recommend printing the main case components (back half, front half, fan shroud, fan shroud extenders, io shield) all in PETG. It's also highly recommended to dry your filament for atleast 4 hours before printing, which can help reduce stringing. If your print has a significant amount of clumps and stringing, then your filament is too wet (this can affect the tolerances)! You can print in other filaments, but make sure the glass transition temp is 80C or higher. PLA is not recommended. Matte/high speed/high flow PETG variants tend to show less line "streaks".

If you want to make your front panel(s) have the same fake wood texture like mine, then download this. And follow the instructions to use it as a modifier in bambu studio. You can print both front panels in PLA. I recommend using a 0.2mm nozzle for the wood texturing, or you may end up with gaps/failed prints with a standard 0.4mm nozzle.

 

Assembly Instructions:

  1. Take off the IO shield and the small bracket next to the cmos battery using a screwdriver (keep the IO shield small screw handy!)

    •  

  2. (optional - heatsink mod) Remove the heatsink from the board. Use the fin scooper tool to straighten the fins underneath where the fan shroud will sit (the side where cmos battery is). I would mark down the line where fan shroud ends with a sharpie, and make sure to not straighten/open the fins past that. I highly recommend the fin scooper over the pliers/scissors method for opening the fins - as the scooper only takes 20-30 mins and has less chance of causing a short. Also the scooper tends to look better overall - you can see in the first picture below that the first 5 fins were the messiest since I tried using the pliers/scissors method. The rest of the fins are much cleaner, since they were done by the scooper. I recommend keeping the first and last 2 fins untouched (see 2nd picture). After straightening the fins, use an airduster to blow away any debris. Don't reattach the heatsink back on if you haven't repasted/applied PTM, as that will be the next step.

    1. Fin scooper tutorial video here. Pry up and down (but not fully so the scooper stays in the fins), while moving the scooper in the direction you want to go in.

    For original fan shroud straighten these fins

    •  For heatsink fan shroud , straighten slightly more (mark with sharpie where fan shroud ends before straightening)

     

  3. (optional - highly recommended) If you haven't already - repaste the APU. Clean off the APU and the heatsink with isopropyl alcohol (90%+), then ideally apply PTM7950. I recommend going slightly larger than the APU die, since it won't hurt things if you make it larger than perfect. But if you cut too small, then you gotta cut a new piece of PTM. Also it's easier to take the plastic seals off if you put your PTM in the freezer for like 10 mins before applying. If you don't have PTM7950, normal thermal paste will work (I did a line in the middle when I used MX4). However, PTM7950 is the best choice for the lowest temps. Reattach the heatsink back to the board. Make sure to apply even pressure when screwing the heatsink back on.

     

  4. Apply pins to the fan shroud, where the pins are sticking up through the holes where the fan will sit. If you are having difficulty fitting the pins in this way, you can also apply the pins to the fan itself sticking down, where they'll attach to the fan shroud.

     

  5. Attach your 120mm fan to the fan shroud. Attach the fan shroud to your bc250. The right wall will go between some unused pins on the board (pic 2). Make sure to line the wall inbetween the pins. Slide the fan shroud on, lining up the pcb with the fan shroud center divot (see pic 2 and 3). Also on one side there is a small extrusion in place that should be flush with pcb to help keep the shroud straightened (see pic 2 and 3). Once the shroud is fully slid on, press down so the two clips on the end latch on (pic 4).

    • put fan on shroud first

    • this pic has fan off to show you how to line up shroud to board, from this position you can just slide it on

    • this is what it should look like once slid on

    push down so that these latches attach to pcb after you lined up everything else from the prior pictures

     

  6. (optional - heatsink mod) If you have the stick on heatsinks, we'll be attaching them now. Make sure you printed out a "heatsink" version of the fan shroud. If you have the 120mm long heatsink: line the stick on heatsink to be flush against the fan shroud gap and remove the conductive tape seal to apply. For the 150mm long heatsink: apply thermal conductive tape, then line the heatsink to be flush with fan shroud gap and apply.

    120mm stick on heatsink comes with thermal tape applied from factory

    150mm stick on heatsink, applying thermal tape manually

     

  7. (optional - heatsink mod) If you printed out one of the fan shroud extenders and you did the heatsink mod step above, you can attach the fan extender now. It fits on right next to the fan shroud. For 30mm thick fans (and using fan shroud for 30mm thick fans), the extender will have a slight gap. You can use tape to seal the gap if you want. If you have a standard 25mm thick fan (using standard 25mm thick fan shroud) then there will be no gap. Important note, I recommend only doing this if you have a rear exhaust fan. Without one, you may slightly worsen your temps (like 1C). This part serves more as a way to protect your fingers/cables against the stick on heatsink.

    25mm thick standard fan shroud with extender

    30mm thick fan shroud with extender

     

  8. Slide your PSU into the back half of the case. If you printed one of the FSP/Apevia/Metalfish profiles - then the PSU's power socket should be flush with the rear side of the case.

     

  9. For FSP/Apevia/Metalfish PSU, attach the internal psu lock to keep the PSU from sliding around.

    1. FSP PSU: Attach lock to the left rail. Slide the lock in from the side until fully attached to inner rail. Fitment may be tight.

      1.  

    2. Apevia PSU: Attach lock to left rail. Fitment will be tight. You may need to press down on the psu a bit, and then slide the lock in from the side. VERIFIED ONLY WITH DUMMY 3D MODEL - PLEASE LMK IF THIS FITS OR NEEDS ADJUSTMENT.

       

    3. Metalfish PSU: Attach lock to underneath the psu (wherever it makes the most sense). NOT VERIFIED YET - PLEASE LMK IF THIS FITS OR NEEDS ADJUSTMENT.

       

    4. Universal Flex PSU: If you printed the universal remix, then use screws to secure your PSU.

       

  10. (optional – cooling) Mount any fans to the rear side of the back half of the case. 40mm and/or 50mm fans will fit. The screws your fan comes with should fit fine, whether they are normal screws or the rubber anti-vibration mounts.

     

  11. (optional - customization) Screw on the custom IO shield with the small screw you saved from step 1

     

  12. Slide the BC250 into the back half of the case, by using the aluminum backplate to attach to the inner rails.

     

  13. Plug in cables. Fan cables/splitters, 8 pin PCIE main power, microfit adapters, etc. DO NOT PLUG IN PSU SHORT YET (pictures have them here, but it's easier to assemble the rest of the case without it plugged in yet).

    Microfit Adapter from mosfet.party

    MODDIY Microfit Cable

     

  14. (optional - usb hub) Break the casing of the USB Hub. I used a small screwdriver to pry/dig near the seams and eventually got the clips undone. Then using some tweezers to get another part off, you can take scissors and cut through the casing. Then slide the internal hub out of the casing. Be very careful with the wires as they have tiny solder points and can be accidentally broken. Attach the usb hub to the inside of the front half of the case. It may require some angled wiggling to get it in. Attach the usb hub brace on the inside to keep it from moving. I tuck the wires under the middle section of brace.

    • line up hub brace on one side then press down

     

  15. (optional - customization) Place any lower custom front plates on the front half of the case before installing the 12mm power button. If the custom plate feels loose, double sided tape is recommended.

    No USB Hub Version

    USB Hub Version

     

  16. Attach the button to the front half of the case, and secure it from the inside with the washer it came with so it doesn't move. Move the two case halves so they are next to each other. For USB hub version: attach usb 3 extension cable to usb hub. Route usb 3 extension to back half of the case. 

     

  17. Attach your button wires to your PSU. The pins you need to short differ between each PSU, so research on reddit/bc250 discord if you need assistance. For the FSP PSU profile, I include a 10 pin adapter clip. If you wish to use this clip properly, you will need to crimp the 12mm button wires with two male dupont single connectors (2.54mm) - then slot them in the same way the picture below shows. For Apevia/Metalfish/Other you may need to solder your wires yourself or create/buy an adapter. I've also done this in a janky method using just a 2 pin dupont connector with a slight bend to the pin.

    10 pin clip adapter for FSP PSU profile only

    2 pin dupont connector with slightly bent pin

     

  18. (optional - customization) Attach a fan grill to the inside of the front half of the case. It should sit flush with the rest of the case. It may be a little loose, but once you slide it over the fan it won't come out.

     

  19. Slide the front half of the case onto your BC250, using the aluminum backplate that line up with the inner rails. Keep sliding the front half of the case until it meets the back half, and both sides attach. Plug in usb extension into one of the back USB ports.

     

  20. (optional - customization) Place any upper custom front plates on the front side. If you print the no side version, double sided tape is required.

     

  21. Enjoy your BC250! Once you do the OS setup, I highly recommend undervolting!

 

Expected Thermals & Noise:

Thermals may vary slightly, depending on a multitude of different factors (thermal paste vs ptm, fan curves, 24CU vs 40CU, 6C vs 8C, overclock, undervolts, ambient temps, heatsink modifications, etc). For reference here's my configuration:

  • GPU: 40CU 2000MHz @940mV (+16CU and +500 MHz from stock)

  • CPU: 3800MHz @1060mV (+300MHz from stock)

  • Heatsink mod (120mm stick on heatsink, with fins straightened under the fan shroud)

     

Game Temps (1080p):

The temps below were taken with regular thermal paste (MX4) and only 6c12t enabled. Since these temps were taken, I have enabled 8c/16t, added async patch, and changed out to PTM. Based on my initial testing, some temps are much lower whereas others remain within the same margin (+-3C). Most if not all of these games have seen a reduction of 3→7C in cpu temps after I changed to PTM, even with the extra 2 cpu cores enabled. Performance has been uplifted quite significantly in all these titles as well.

 

Comparison to “Most Optimal” Heatsink Mod:

You may be wondering how does this case compare to the most recommended solution of opening the fins in the middle and putting fan(s) directly on top?

 

Well, I did an apples to apples comparison thanks to the data from this post. I matched everything I could, 40CUs 1900MHz at 880mV w/ a single p12 pro but with my own heatsink mods (opening fins on single end and the stick on heatsink). Running furmark for 2 mins. Also, my test was done without any rear fans plugged in.

 

So around 3C cooler when matching: fan model, gpu frequency, gpu voltage, and PTM. Differences are from the fan shroud and stick on heatsink modification.

Pictures from my PTM Tests:

 Video

Comparison to Other Cases

Image preview

This is nyacom's industrial style case. It's pretty similar in terms of cooling design, as both my case and nyacom's uses the stock cooler with a single fan. Also was one of the few cases with thermal benchmark results. It's a pretty awesome design, so check out the printables page if you're interested. For the benchmarks, my case was using a quiet tuned fan curve. Nyacom's data was based on furmark GL 1920x1008 with temps taken after 10 minutes. I repeated those tests with the same criteria. For larger images, right click the image and click open image in new tab.

 

24CU @1500MHz

40CU @1500MHZ

Nyacom's Industrial (no gpu gov)

76C

85C

My Case (no gpu gov)

66C

72C

My Case w/ gpu gov

63C

68C

My Case w/ gpu gov and fan 100%

50C

55C

Comparison to AIOs/Modified CPU Coolers:

To be fully transparent, this case does lose out quite handily to AIO solutions or modified cpu coolers onto the bc250 (like the jf13k). Those solutions will get you 50→60C in almost all games, and you'll likely not even hit 70C in stress tests. However, my intent for this case was to never compete with those solutions. This case was meant to provide adequate cooling for gaming with minimal (optional but extremely easy to do) modifications using the stock heatsink.

Keep in mind the price for an AIO/JF13K will be $50 or more. Also, you will need to buy additional heatsinks for things like the VRMs and other components. This case can be cooled on a $6 arctic p12 pro alone.

 

Comparison of all Thermal Improvement Mods:

Ranked from most to least effective.

  1. Undervolting (gpu governor)

    1. Highly recommend doing this. Stock voltages run the card HOT. Undervolting can lower temps 15C or more as well.

       

  2. PTM7950

    1. Gives the most thermal improvements out of all the physical mods. Highly recommend doing this, it can lower temps 10C or more.

       

  3. Opening Fins & Stick on Heatsink

    1. Opening the fins increases available airflow to the stock cooler. Stick-on heatsinks increase total heatsink surface area, making the fan have to do less work. Both are highly recommended. With both combined, it can lower temps up to 10C as well.

       

  4. Repasting with regular thermal paste (MX4)

    1. Lowered my temps by around 5C from the dried out paste that it came with. It's okay if this is your only option, but PTM is much much better.

       

  5. Using a 30mm thick fan with better airflow and static pressure (normal fans are 25mm thick)

    1. Up to 3C cooler when pushing my highest OC. I throttle doing furmark with the 25mm thick fan (arctic p12 pro), but don't throttle using 30mm thick fan (sudokoo mach120). Also it's quieter at higher RPMs which is the main benefit.

       

  6. Adding rear exhaust fans

    1. Lowers temps by like 1C with one fan. With 3 fans, you might see up to 3C lower

       

  7. Additional airflow to backplate from fan shroud

    1. No difference in APU temps. There's no temp sensors for the ram, but probably lowers ram temps by a couple degrees.

  8. Changing thermal pads

    1. No difference, even when I swapped out crusty pads. Though, replacing the VRAM pads with 3mm thick pads may help with VRAM longevity by helping transfer more heat to the backplate from the ram.

  9. Fan shroud extender

    1. Without an exhaust fan this may worsen cooling about 1C if not fully sealed. With a full seal and a single exhaust fan I got around 0.5C lower temps. The shroud extender is more beneficial for protecting fingers/cables than for cooling improvements.

  10. Fan grills

    1. May slightly reduce cooling (1C) due to more restricted airflow

 

Fan Noise:

See the video above which shows fan noise at 65C (around 45% fan speed, 1350ish rpm). Camera was about 3ft (1m) away from the bc250. Fan grill was on, which increases noise by maybe a half a dB at this fan speed.

With my fan curve I never go above 2000rpm except for stress tests. For gaming, I'm in the 1200→1800rpm range, which is quiet or slightly noticeable. I recommend tuning your fan curves so you don't hit 2500rpm or higher, as at that level of noise it can start to be annoying.

 

Credits:

  • morph91 for the original model

  • lolheyaj for apevia profile on original model (used for my apevia profile measurements)

  • jinson for creating the universal psu remix

  • wezla for fan grill design inspiration

  • Noctua for second fan grill design

  • Stringhigh for wood modifier I used for my front panels

  • C3D for demon slayer front plate hueforge design

  • Abi for cyberpunk edgerunners front plate hueforge design

Tags