Maestro Dock – Pepper Mill & Reservoir Holder

Maestro Dock — Mill Stand & Stackable Reservoir Holder

Compatible with the Peugeot Maestro u'Select pepper bar.

A clean, minimalist modular storage system for the Peugeot Maestro u'Select "pepper bar" — the mill with interchangeable pepper reservoirs. Keep the mills and every spare reservoir upright and within reach, and stack the trays into a tower when you have more reservoirs than counter space.

Overview

The Peugeot Maestro system is brilliant — one mill, sealed glass reservoirs, premium peppers — but once you unbox it there's no tidy home for the mill and the reservoirs you're not currently grinding. This set fixes that, and it grows with your collection:

• A mill stand that cradles two mills upright, side by side.

• Reservoir trays that keep your spare interchangeable reservoirs standing neatly instead of rolling around a drawer.

• A stack, not just a tray. Add reservoirs and go vertical — the trays stack with connector columns to hold well more than four reservoirs in the same footprint.

Every piece shares the same soft figure-8 silhouette and 60 mm cradles, so a single tray or a full tower reads as one coherent object on the counter.

Key Design Elements

• Stackable, modular tower. Trays link vertically with the connector columns to build as tall a stack as you need — the footprint stays the same while capacity grows.

• A base and a middle piece. One tray has locating holes on both top and bottom, so it works as the base of the stack or as a mid-layer — mix and match to size the tower to your set.

• Snug 60 mm cradles. Each pocket is Ø ~60.7 mm and ~11.5 mm deep — deep enough to hold a mill or reservoir securely upright, shallow enough to lift out in one motion.

• Two variants, one look. The mill stand (150 × 80 mm) and the reservoir trays (160 × 80 mm) are visually identical from across the room, so mixing them on a shelf still looks intentional.

• Stable, low-profile base. A wide 80 mm footprint and rounded figure-8 outline keep the loaded holder from tipping, even with a full mill in place.

• Print-friendly by design. The mill stand prints support-free, pockets facing up. For the reservoir holders I ran supports around the connector holes to be safe (see print settings).

Technical Specifications

Material: PLA (printed in Bambu PLA Matte, black — PETG works well too)
 

Print settings

• Printer: Bambu Lab (0.4 mm nozzle)

• · Layer height: 0.20 mm (use 0.16 mm HQ for a finer finish)

• Walls: 2 perimeters

• Infill: 15% gyroid

• Supports: mill stand — none. Reservoir holders — I used supports for the connector holes to be safe; they may not be strictly required, so try without first if you like.

• Connector columns: 30% gyroid infill (set automatically), a 0.25 mm chamfer top and bottom, and a brim. Print these a little slower for clean, strong results.

Assembly: Clean off any brim, stack the trays on the connector columns, and drop your mills and reservoirs in — no screws. If your columns fit snugly, no glue is needed. But tolerances vary from printer to printer: if the fit feels at all loose, add a couple of drops of superglue (CA glue) into the column joints so the stack stays solid when you lift it.

What's included / parts

• Mill stand — holds two mills upright.

• Reservoir tray (base/middle) — the piece with top and bottom locating holes; use it as the foundation or stack several.

• Connector columns — the vertical pieces that lock stacked trays together (cross-section ~27.5 × 29.5 mm, matched to the tray holes). These are functional parts, not print supports.

Design Features

• Stacks to hold more than four reservoirs — go vertical as your collection grows.

• Holds the two mills upright in the mill stand and your spare reservoirs in the matching trays.

• One-hand lift — grab and go while cooking.

• Coherent, modern silhouette that suits an open kitchen shelf as much as a drawer.

• Scales to your set: print one reservoir tray or a whole tower, depending on how many reservoirs you keep loaded.

Did you print it? I'd love to see your setup! Please upload a make and leave a review to help others find this model.