Customizable ZX-4R Knee Grip and Fairing 3D Scan (Right Half).
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
3D scan and knee grip addon for ZX-4R/ZX-4RR
- Rating
- 5 / 5
- Likes
- 2
- Downloads
- 6
- Makes
- 0
- Views
- 47
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- Creative Commons — Attribution — Share Alike
Intro:
If you found this useful, please do leave a like and a comment for any possible improvements or reviews.
I mainly wanted to just scan the knee grip part to create a knee grip that actually grips the rider well. The stock is just too slippery and shallow to be really useful, in my opinion. Since I had to remove the whole section to take upstairs to my computer might as well scan the whole thing. Most of the models were scanned at 0.2mm resolution, except for the outer scan, which was scanned at 0.3mm resolution.
Models Included:
Fairing Scans:
Fairing Outer Raw Scan.
COVER, KNEE GRIP, OUTER, RH, 14093-5453-H8
COVER, KNEE GRIP, INNER, RH, 14093-0964
Bracket Parts:
BRACKET, KNEE GRIP COVER, RH, 11058-1068
Bracket modified to remove the rubber damper.
Bracket COLLAR 92152-0017
Knee Grips:
Knee Grip Addon Blank V1: Stock Looking (So that you can make your own custom one).
Knee Grip Addon Blank V2; Chamfered (So that you can make your own custom one).
Knee Grip Addon Knurling.
Knee Grip Addon Noise.
Knee Grip Labyrinth.
Original Reduced Scan used to make the mesh for reference
Making A Custom Grip Texture:
To make a custom knee grip, download the blank and go to bumpmesh.com .
Upload the model into the website. You can also run the program locally from GitHub.
Orient the model upright by rotating it or placing it on a desired face as shown below.


Select the texture pattern that you like,
Adjust the texture smoothing to your preference; invert for knurling texture or if you just want to.
Set texture height/thickness to 5 mm. For whatever reason, the output model is approximately displaced by half of the set value (so an input of 5 will only displace the mesh by 2.5mm in this case). I have no idea why this happens. You will have to mess around with this value to get your desired results.
UV scaling to adjust the size (I prefer 15-25 for most textures).
Set masking to "Include" only and "Fill".
Set the masking max angle to 4-5° and then click on the middle of the grip area.
Refine the edges using the brush to add and remove extra selection if needed. The next step will smooth out the results from this step, so don't be too worried about the mask edges if they look a little rough.
Smooth mask distance to 2- 2.5 mm. Set to linear.
Export the final model (0.2- 0.3 mm resolution recommended)(1-1.5 million polygons).
Print the grip texture preferably in TPU and then secure it with the stock screw (M5x18mm). The model should only be 1mm thicker than the stock setup, so you should be easily able to secure it with the stock screw. The grooves will align in place. You could also use 3M 468MP Adhesive Sheets, provided you clean the surface well and print in ABS
Disclaimer:
All models were made by me and not by AI. Not for commercial use. All renders and cleanup were done in Blender.
The friction mounting points could not be scanned fully due to the deep geometry. This should not affect the functionality, but it represents an aesthetic shortcoming that you will only notice when you remove the part. YOU WILL most likely have to drill out the holes for the plastic screws a little that attach the outer and inner parts. The default hole diameter is 3.9mm. I have attempted to clean up the geometry as best I could care to, but you may have to do some work, you lazy f***.
