inspired by Honda Accord VII – Moving Wheels – 1:18, 1:24 & 1:64
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Honda Accord VII sedan with moving wheels, separate rims, TPU tires and Honda center caps. Three scales included.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 34
- Makes
- 0
- Views
- 116
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Vehicles
- License
- Standard Digital File License
Honda Accord VII
A printable model of the European Honda Accord VII facelift sedan, prepared for FDM printing with freely rotating wheels, separate rims, flexible tires and Honda center caps.
Available in 1:18, 1:24 and 1:64. Each scale includes dedicated wheel parts and mounting dimensions, so you can print the supplied files directly at 100% size.
Printed and tested
The 1:24 version shown in the photos and videos was physically printed and tested. The body, wheel fit and assembly were checked on the printed model.
The 1:18 and 1:64 versions are also included. Their geometry and wheel clearances were checked digitally; these two scales have not yet been physically tested.
Included files
Each scale contains four STL files:
Body — one body with integrated wheel mounts.
Rims — a complete set of four rims.
Tires — a complete set of four tires.
Caps — a complete set of four Honda center caps.
That gives 12 STL files across three scales, with 13 printed parts per model.
The files are supplied without generated supports. Screws are required separately.
Model features
Freely rotating wheels mounted with screws.
Integrated axle tubes connected to the body.
Separate rims and tires for easy material and color selection.
Ten-spoke rims with recessed screw-head pockets.
Flexible TPU tires with circumferential grooves.
Separate center caps with a raised Honda H.
Simplified underbody with a flat printing orientation.
Closed doors, hood and trunk, with no separate interior.
Adapted mounting clearances and reinforced small wheel details in the 1:64 version.
Required screws
1:18
4 × M2 × 12 mm
Maximum head diameter: 4.2 mm
Maximum head height: 2.0 mm
1:24
4 × M2 × 10 mm
Maximum head diameter: 4.2 mm
Maximum head height: 2.0 mm
1:64
4 × M1.4 × 4 mm
Maximum head diameter: 2.6 mm
Maximum head height: 1.2 mm
Use non-countersunk screws with a flat bearing surface beneath the head. Screw length is measured beneath the head.
The screws engage directly in the printed body mounts; nuts are not required. Check the head dimensions of your screws before assembly.
Wheel assembly
Remove supports and clean any first-layer expansion from the mating edges.
Fit each flexible tire onto its rim.
Insert the screw through the rim and carefully thread it into the body mount.
Leave a small amount of axial clearance so the wheel rotates freely.
Check all four wheels for rubbing before installing the center caps.
Secure the caps with a small amount of glue around their mating edges if needed.
Do not overtighten the screws. They should retain the wheels without clamping them against the body.
The caps use a clearance fit and are not snap-fit parts. Keep glue away from the screws and rotating surfaces.
Recommended print orientation
Body: print upright, resting on its flat underside.
Rims: print with the inner face on the build plate and the outer face upward.
Tires: print flat on their sides.
Caps: print with the flat back on the build plate and the Honda H facing upward.
Use local supports for body overhangs where needed, particularly beneath the mirrors and bumper areas. Inspect the wheel arches in your slicer.
The rims, tires and caps are designed to print without supports in their supplied orientation.
Suggested FDM settings
Body, rims and caps: PLA or PETG.
Tires: flexible TPU.
Nozzle: 0.4 mm for the main parts.
Layer height: 0.15–0.20 mm for 1:18 and 1:24; 0.10–0.15 mm for 1:64.
Perimeters: approximately 3 for the body and 3–4 for the rims.
Center caps: 100% infill.
Supports: local supports for the body as required.
For the small 1:64 center caps, a 0.25 mm nozzle is preferable for the raised H and fitting details. When using a 0.4 mm nozzle, check that these features appear correctly in the sliced preview.
The tires are designed for an elastic fit on the rims, so TPU is recommended rather than rigid filament.
Print the supplied files at 100% scale. Avoid resizing a completed kit to another scale, because screw dimensions and assembly clearances do not scale proportionally.
Printer calibration, material and first-layer expansion can affect the fit. Print one rim, tire and cap first to check the assembly before printing the complete set in 1:18 or 1:64 scale.