Cordless Blackout Blind for Narrow Door Glass – Push Up, Pull Down, Let Go, Sealed Side Rails
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Slim cordless blackout roller for a narrow door lite: push the bar up, pull it down, let go. Sealed rails, captive bar.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 0
- Makes
- 0
- Views
- 23
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other House Equipment
- License
- Creative Commons — Attribution — Noncommercial
A slim, cordless blackout roller blind for the narrow frosted glass lite in a door. The ready kit is for a half-height lite of about 190 x 990 mm visible glass (for example Westag LA-18-21,5 doors). Hold the bottom bar, push it up to open, pull it down to close and let go - there is no cord, chain, crank or magnet. A printed head (58 mm tall, 38.4 mm deep, nothing on its front) sits on the flat door face above the glass. Inside its end block, two catalogue constant-torque strip springs drive the roll directly through a printed hex dog, with no gears; they keep the fabric taut but do not have to balance the blind, which is why such a narrow cordless roller is possible. Felt-faced brake shoes in the side rails and a ballasted bar are designed to hold the bar at any height. The fabric edges run inside two aluminium U-rails taped on the glazing beads, and the bar runs captive inside the rails, so it cannot swing or slap the glass when the door slams. A print + buy kit.
Validation status (please read): designed and checked in CAD and in the slicer; spring tension, brake hold, effort and light blocking are calculated or shown in CAD. Nothing has been physically printed, assembled or tested. All pictures are renders of the CAD model with bought-part stand-ins, or drawings - none is a photograph. The night pair is an illustration of the intended state, not a measurement.
Features
Push the bar up, pull it down, let go: no cord, chain, crank, loop or magnet in any position. On a half-height lite the bar closes at about 0.8 m - no stooping.
Designed to hold at any height (calculated, not measured): at the low end of the assumed felt friction the brake shoes hold about 2.5x the worst calculated resting force on the bar; moving the bar takes at most about 5.2 N.
Catalogue springs, not a custom part: two SDP/SI A 3X51-20002 constant-torque motor springs (rated 14.7 N·mm each, rated fatigue life 2,500 cycles - about 7 years at one a day) on the roll's own hex dog. No gears, no threaded parts in the drive.
Sealed edges: the fabric edges run inside aluminium U-rails with black felt; in the CAD plan section the edge light has no straight path (0 of 4,510 test rays get through). Light blocking itself has not been measured; a faint glow can remain at the corners.
Captive bottom bar: its 5 mm steel rod ends run in the brake shoes inside the rails - no swinging, no clips.
Slim: 38.4 mm head (about 39.5 mm from the door with the mounting tape), rails 18.1 mm, bar 19 mm. The ends of travel are fixed by the parts, so the roll cannot be over-wound.
Will it fit my door?
Ready kit: about 190 mm wide visible glass with 22 x 5 mm beads, from 600 mm up to about 1030 mm tall with 480 g/m² fabric (up to about 1010 mm with 500 g/m²; 680-1130 mm with 400 g/m²). Only the cut lengths change: rails = glass height + bead width + 22 mm, fabric = glass height + bead width + 140 mm.
Other doors or fabrics: change the parameters in model.py (glass width 90-196 mm, glass height 600-1480 mm, bead width 15-25 mm, bead height 0-6 mm, fabric thickness and weight) and export again; the model chooses 1 or 2 springs, the ballast flats and the brake-spring force, and rejects sizes or fabrics where no choice meets the margins.
A flat frieze of at least 59 mm above the glass. For 1560 mm full-height strips see the crank-operated Slimline Crank Blackout Roller instead.
Which files?
cordless_blackout_roller_190x990_plate1_fascia.3mf, _plate2_lip_rail.3mf and _plate3_parts.3mf - three 220 x 220 mm plates, 19 pieces including the spool jig tool, brims and 4-perimeter small parts set.
STL files of every part (spool_arbor = the spool jig).
model.py + calc_mechanism.py - the parametric CadQuery source and its spring / brake calculation.
Print settings
ASA, black or anthracite, for every part (behind glass the parts can reach 46-76 °C in sun - PLA and PETG soften too low). Enclosed printer and good ventilation.
0.4 mm nozzle, 0.2 mm layers, 15 % gyroid, 3 perimeters (4 on the spool halves, plugs and shoe halves), no supports - as placed in the projects; the fascia and lip rail sit at 45° on their own plates.
Fascia 4 h 56 min, lip rail 1 h 1 min, all other parts 8 h 46 min - about 159 g of ASA in total (PrusaSlicer 2.9.6 estimates, generic profile). PrusaSlicer shows a stability note for the tall-walled fascia (2 mm brim set).
Bought parts (ready kit)
Rough cost about EUR 110-150 including the two springs shipped from the US (an estimate, not a quote).
Blackout fabric, PVC-laminated or coated, 400-500 g/m² and at most 0.35 mm thick (10 layers folded must measure 3.5 mm or less), white back: 213 x 1152 mm.
Aluminium tube 16 x 1 mm: 215 mm. Aluminium U-profile 12 x 10 x 1.5 mm, 2 m stock: 2 x 1034 mm.
Constant-torque motor spring SDP/SI A 3X51-20002 (part designation): 2 - from the SDP/SI online shop (US), in Europe only through AMETEK Hunter Spring distributors on inquiry. The neighbouring sizes -20004 / -20005 are not substitutes.
Steel dowel pin 3 x 22 mm (ISO 8734); 0.8 mm piano wire, one 9.4 mm and one 6.8 mm piece; a 1.3 mm drill bit.
Steel rod 5 mm: 214 mm; ballast: 2 bright steel flats 15 x 4 mm cut to 189-190 mm.
2 compression springs OD 3 mm, about 3.0 N at 4.6 mm, free length 5.5-6.0 mm.
1 mm black self-adhesive wool felt, 2 mm black foam strip, black acrylic-foam tape about 1.1 mm, thin double-sided tape, fabric glue, 2-part epoxy, gel CA glue, work gloves for the spring strips.
Assembly (summary)
The full step-by-step procedure (19 steps plus service) is long; here are the key points - read it all before you start, and wear gloves for the thin, sharp spring strips.
Cut the tube, rails, rod, steel flats, the two wire pieces and the fabric; trim both bottom fabric corners (6.5 mm off each side over the bottom 48 mm).
Roll and bar: epoxy the motor-end plug (with the hex dog) and the idle-end plug into the tube; tape the fabric on, white side toward the glass, leaving the roll on the door side; wind it on. Hem the bottom round the 5 mm rod, slide it into the bar's channel, slide in the two steel flats and tape the pocket ends.
Spring set on the printed spool jig: clear the output halves' keyhole channels with the 1.3 mm drill; anchor each strip end round its wire in an output half; turn each output half clockwise onto the jig's hex rod until its notch drops over the rib. Check each strip path: it must cross between the two drums like the middle stroke of an S (a C means the coil is upside down). Glue each anchor wire with gel CA.
Head: epoxy the fascia onto the motor block; felt strip at the slot. Drop the spring set into the chamber from the open back and push the pin in from outside, leaving 1.0-1.5 mm proud. Push the jig in from outside and turn it counter-clockwise about half a turn until it drops onto the pin end.
Couple the roll: with the fabric fully wound and the bar held against the head, slide the roll in so the hex dog passes through both output halves and pushes the jig out (pull the bar away from the head a little if the dog stops). Press the pin home, press in the end cap.
Direction check: pull some fabric down and watch both strips - each must wind onto its output half with a steady pull back. If not, take the spring set out and correct it.
Slide on the idle block (no glue); push the lip rail in from the door side between the door and the fabric.
Mount: clean the door, foam-tape the head 1 mm above the top bead; felt inside the rails; assemble each brake shoe (felt faces, spring between the halves) on a bare rod end; offer each rail over its shoe and tape it to the bead, using the bar as the spacing gauge. Glue the rail end caps in.
Check: let go at a few heights - the bar must stay; fully down the shoes rest on the end caps; fully up the bar stops under the head with the fabric taut.
Service: if the bar creeps, add a 0.5 mm plastic shim behind each brake spring; if it is too stiff, remove one or fit a softer spring (about 2.5 N). Never cut the fabric while the roll is coupled to the springs; keep the jig for spring or fabric changes.
Limitations
Nothing printed or assembled yet. Felt brake friction on aluminium is assumed (0.15-0.35) and felt settles over time; spring torque tolerance (±10 %) is assumed.
The springs are a catalogue part from one maker (SDP/SI, US) - outside the US they must be imported.
The spring set must be built exactly as described; a mistake shows at the direction check and means taking it out again.
The kit fits the stated range only; fabric 400-500 g/m² and at most 0.35 mm thick.
More parts and cost than a chain cassette blind - this is for people who want no cord or crank and sealed edges and a captive bar.
Taped parts depend on the door surface: do a pull test; never screw into plastic clip beads or hollow-core door skins.
Not certified to any blind-safety standard (it contains no cord, chain or loop; the spring strips are enclosed once the head is on the door).
Pictures
Renders of the CAD model and drawings, not photographs: the blind on a half-height door lite (cover), the lite open vs closed at night (illustration, not measured), fully open, push / let go / pull, the spring end of the head, the parts exploded, the dimensions and the side-channel section with the intended light path. Westag and SDP/SI are named only as fit and part references; not affiliated.