1 / 5
Replacement control knob for the vintage Atag Erin gas stove (Ø8 mm double-D shaft) — image 1
1 / 5

Replacement control knob for the vintage Atag Erin gas stove (Ø8 mm double-D shaft)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Replacement knob for the vintage Atag Erin gas cooker. Fits the Ø8 mm double-D shaft and 43 mm bezel. Tested.

Rating
0 / 5
Likes
0
Downloads
2
Makes
0
Views
28
Reviews
0

Updated at source:

Model information

Category
Kitchen
License
Creative Commons — Attribution — Share Alike

The Atag Erin is a Dutch gas cooker from the 1950s-60s: green enamel, chrome bezels with the 0 / 1 / 1/8 scale, and cream-coloured bakelite control knobs (part no. 4085). The cooker itself is excellent, but the knobs crack with age and are no longer available. This is a replacement knob modelled on the original, measured on my own Erin.

What it is

  • Ø42 mm disc with a straight 5 mm rim, a rounded shoulder and a fin that serves as grip and pointer, 24 mm high in total, same as the original. The fin slopes off on the back and has the rounded corner on the pointer side, so it looks like the old knob next to the remaining original ones.

  • Fits the Ø8 mm brass shaft with two flats (6 mm across the flats, flats 10 mm long). The bore is 20 mm deep: the first part is round so the round part of the shaft can enter, then double-D. The knob can be mounted two ways (180° apart); fit it with the pointer on 0 with the valve closed.

  • Drops into the 43 mm chrome bezel with 0.5 mm clearance per side. The back has a bowl so the two screw heads next to the shaft run free, and a hub exactly like the original.

  • Push-to-turn works. Fully pushed onto the shaft the back of the knob floats 1 mm above the bezel floor, enough to press the valve release.

  • Held by the original slotted M5 grub screw, radially through the pointer end, pressing on the round side of the shaft. The screw taps its own thread in a Ø4.8 mm hole over 6 mm; no insert needed. A drop of oil on the screw makes it easier.

  • No metal trim strip (the original has a decorative strip in the fin). It isn't missed.

Does it fit other stoves?

The dimensions are from an Atag Erin. Any stove with an Ø8 mm double-D shaft (6 mm across the flats) and a bezel of about 43 mm might work, but check the shaft, the depth and the position of the screw heads first. The STEP file is included so you can adjust it in your own CAD.

Printing

  • Print it as oriented: back on the bed, fin up. That gives the best surface on the shoulder and the fin.

  • Supports inside the bowl only. The hub floats 6 mm above the bed, so the bowl needs support; nothing else does. In PrusaSlicer: Support on build plate only. The bowl is open towards the bed, so the support sits only in there and nothing touches the visible outside.

  • PETG sticks to its support, so use settings that let it release: Organic style, top contact Z distance 0.2 mm (one layer at 0.2 mm layers), 2 interface layers with an interface pattern spacing of 0.4 mm, XY separation 1 mm, Don't support bridges on. With these it pulls out in one piece.

  • Brim: outer brim only, 3-5 mm. An inner brim fills the bowl opening and is hard to remove.

  • 0.20 mm layers (0.15 for an even smoother shoulder), 4 perimeters, 25% gyroid infill. About 11 cm³, 40 minutes on a Prusa CORE One.

  • PETG recommended: it tolerates the heat next to a burner better than PLA. Cream or ivory PETG matches the original knobs best.

Files

  • atag-erin-gas-knob.stl: the knob

  • atag-erin-gas-knob.step: for remixing in your own CAD program

Not affiliated with Atag. Designed in FreeCAD with a parametric script; measured and test-fitted on an Atag Erin in October 2026.

Tags