Counting matching models…
Replacement blade for the original Einhell Trimmer GC-CT 18/24 . If you are annoyed with your trimmer blades constantly breaking, consider using my string-trimmer head. It can use string-trimmer string or TPU plastic, both of which are…
Print approx. €0.10–€0.13 excl. taxPreliminary estimate for one variant
Transforms your Einhell Single-Blade Trimmer into a string trimmer. Use at your own risk, the wire might get loose and fly off at high speeds, which can lead to injuries, always make sure to wear proper safety gear. Printing Choose an…
Print approx. €0.33–€0.41 excl. taxPreliminary estimate for one variant
You need for each arm 5 M4x14mm nuts. It is recommended to use supports on plate only.
Print approx. €4.02–€4.91 excl. taxPreliminary estimate for PETGSource material: PET
Replacement part for Seat Ateca parcel shelf. Might fit other car models but didn't test that. Print the pins as shown in the picture (more strength). I used a 0.3 [mm] layer height (should only be functional) and PETG and it works like a…
Print approx. €0.24–€0.29 excl. taxPreliminary estimate for PETGSource material: PET
EN: The original plastic clip on the Tractive CAT Mini GPS tracker tends to break over time — this model is a direct replacement that snaps right onto your cat's collar just like the original. What's new in version 2: Reinforced mounting…
Print approx. €0.58–€0.71 excl. taxPreliminary estimate for PETGSource material: PET
A replacement head for the Einhell Trimmer GC-CT 18/24. It replaces the original single-blade-head with a multi-blade head. (The provided .stl files only have three blades, but you could go with more by editing the .scad file, or using…
Print approx. €0.76–€0.93 excl. taxPreliminary estimate for one variant
If you already used my Label-Covers or Drawer Inserts for the Allit Basic 33 / Allit VarioPlus Hobby 33 drawer inserts (Also sold by Aldi Workzone “Kleinteilemagazin” or Lidl Parkside drawer), you may be interested in this one as well: I…
Print approx. €1.95–€2.38 excl. taxPreliminary estimate for one variant
This Thing is a Renault Modus trunk shelf clip. It's very hard to find this one in car parts shops, without this trunk shelf is very unstable and may fall while driving. Tried to find this clip on scrapyard with no luck. This clip may…
Print approx. €0.70–€0.86 excl. taxPreliminary estimate for one variant
Whistle not included! There are two variants: Signal-Whistle-Replacement.stl Version with cutout for a 42mm x 4.5mm (diameter) ferrocerium rod. Signal-Whistle-Replacement-Simple.stl Non-functional spacer part, just to keep the space…
Print approx. €0.36–€0.44 excl. taxPreliminary estimate for PETGSource material: PET
My kids kept destroying the cards when we play Exploding Kittens so I picked up sleeve protectors to help them last longer. On the plus side the cards are in great shape. On the other side, they no longer fit in the tray that comes with…
Print approx. €4.36–€5.32 excl. taxPreliminary estimate for one variant
I designed these for my mom after she lost one of her original ones. I used a ballistic chronograph to compare to the originals and was unable to see any difference in performance. Printing notes: The casing is printed in PETG, and the…
Print approx. €0.26–€0.32 excl. taxPreliminary estimate for PETGSource material: PET
These are building blocks to replace any missing blocks (or to recreate the entire set!) from the Grimm's Stepped Pyramid Puzzle Block set. I bought a used “stepped pyramid” set that we found at our local thrift store that was missing one…
Print approx. €1.56–€1.91 excl. taxPreliminary estimate for one variant
Replacement for Reef boardgame mini expansion, in case you lose one fish. https://boardgamegeek.com/boardgame/253274/reef-kings-coral Print instructions Category: Toy & Game Accessories Summary Replacement for Reef boardgame mini…
Print approx. €2.30–€2.82 excl. taxPreliminary estimate for one variant
This was a quick replacement for the original hitching rail, which was broken and made from a material that could not be glued back together. I recommend printing it upright to get a nice round rail. I used PLA from Das Filament in…
Print approx. €0.69–€0.84 excl. taxPreliminary estimate for one variant
Replacement top cover for Kenwood Chef Major Classic. Beware: The tabs are fragile
Print approx. €1.73–€2.11 excl. taxPreliminary estimate for one variant
Design is at the end of video
Print approx. €0.56–€0.68 excl. taxPreliminary estimate for PETGSource material: PET
This model is a replacement for the reverse/brake side of the trigger on the FlySky Noble NB4/NB4+ radio. I accidentally broke the Medium size, and then the Small size broke on me unexpectedly. There is definitely a weak spot in the…
Print approx. €0.18–€0.22 excl. taxPreliminary estimate for PETGSource material: PET
I designed this to hold a good lens from an old magnifier. I tried several methods of holding the glass and ended up with simple (but not very elegant). There is a small cut in the circle to allow you to work in the glass - then glue it…
Print approx. €1.97–€2.41 excl. taxPreliminary estimate for one variant
My Dolce Gusto (Nescafe) was missing a leg. I had to design a quick replacement part for it. It's something super simple that solved a real problem in my kitchen. Print instructions Material: PLA (I used PolyTerra Saphire Blue) Infill:…
Print approx. €0.08–€0.09 excl. taxPreliminary estimate for one variant
Print in vase mode. Use a solder iron to make small holes to mount.
Print approx. €0.18–€0.22 excl. taxPreliminary estimate for PETGSource material: PET
A leg of my Crate and Barrel couch had shattered so I modeled a replacement. Might work for you as well. Print instructions Print with a pretty tight infill (did 20% 3D Hexagon) because a lot of weight will be put on it. Used PLA and…
Print approx. €1.07–€1.31 excl. taxPreliminary estimate for one variant
I found this useful model on the Internet. If you are one of the few people in the world that still has a TI-99/4A Peripheral Expansion Box (early version), this file may come in handy some day. *** This is NOT my original design, I'm…
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for one variant
I needed a quick replacement for a Pfaff Variomatic 6085 til the new aluminium one arrived. Fits perfect.
Print approx. €0.21–€0.25 excl. taxPreliminary estimate for PETGSource material: PET
One of the corners of my mother's SuperFrame quilting frame corners has been broken for 10+ years, and it had been ridiculously expensive and nigh on impossible to find replacements for it due the brand no longer being in production (as…
Print approx. €0.97–€1.18 excl. taxPreliminary estimate for one variant
This is a print-in-place replacement wheel for an old series metal Canadian Magen David Adom donation box. Required hardware One M3x20 socket head screw per wheel Printing instructions Print the .stl file as-oriented (outside part of the…
Print approx. €0.41–€0.50 excl. taxPreliminary estimate for one variant
This is a redesigned power slider switch button for the Black & Decker Cordless Leaf Blower (LSW321). My aging mother no longer has the full function of her hands due to arthritis. This presents a problem as she is unable to apply the…
Print approx. €0.96–€1.17 excl. taxPreliminary estimate for one variant
I dropped my kit, and the revolving bit carrier part broke it's pivot on the top side. Modeled it and print turned out excellent.
Print approx. €1.16–€1.41 excl. taxPreliminary estimate for PETGSource material: PET
Replacement plastic part from Rog Strix Fusion 300 headset Print with supports, 100% infill, brim 6mm, 4 perimeters.
Print approx. €1.22–€1.50 excl. taxPreliminary estimate for PETGSource material: PET
The main problem with finding a replacement was that the holes in the wall are 20 mm apart and I didn't want to drill more holes. Since I couldn't find a suitable holder in the DIY store, I simply modeled a replica of the old holder. The…
Print approx. €2.50–€3.06 excl. taxPreliminary estimate for PETGSource material: PET
Replacement handle for Sterilite Stack & Carry handle box organizer.
Print approx. €0.77–€0.94 excl. taxPreliminary estimate for one variant
A print-in-place Viewmaster lid that replaces your old one. Here's the single one-print piece: https://www.printables.com/model/303021-willy-wonka-everlasting-gobstopper If you found this useful, it would bring me great joy to see your…
Print approx. €3.47–€4.24 excl. taxPreliminary estimate for one variant
This is a small replacement gear featuring a 10-tooth rounded cycloidal (flower-style) profile , recreated from the original part using caliper measurements and reference photos. Specifications 10 rounded (cycloidal) lobes Outside…
Print approx. €0.08–€0.10 excl. taxPreliminary estimate for one variant
The clip will now hold the phone tight and it will not fall out. Increased griping strength. Well I guess I am a little OCD. The D ver of this really fits nice and snug, so I am now happy. Also if you have an MK4S with HP nozzle I…
Print approx. €0.36–€0.44 excl. taxPreliminary estimate for PETGSource material: PET
Description Replacement snap clips designed to repair broken locking tabs on the Loxone NFC Code Touch. A common failure point of this device is the small plastic snap clips, which can break during disassembly or installation. When this…
Print approx. €0.21–€0.25 excl. taxPreliminary estimate for one variant
replacement button for hardhead childgate
Print approx. €0.64–€0.78 excl. taxPreliminary estimate for PETGSource material: PET
Internal shaft for Probata thermostat. The plastic parts of these thermostats gets very brittle over time. Making new shafts connecting the potmeter to the adjuster wheel extend the life of these units. This print alone has saved me close…
Print approx. €0.20–€0.24 excl. taxPreliminary estimate for PETGSource material: PET
Replacement piece to plastic mounting plates above earphones.
Print approx. €0.76–€0.92 excl. taxPreliminary estimate for one variant
The bracket of my HyperX Cloud 2 headset broke, so I modeled and printed a new one.
Needed a replacement nut for our lampshade, so I made one. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 20% Filament: Prusament PETG Signal White
These are not go over guards and replace the stock removable cage! (See Pics) They are tested in my own reef tank! They provide a cleaner look then a go over guard and the added safety of one! No more daily cleaning of quick to clog foam…
========================================================== UPDATE: I have released an improved version v3 which can be found here ========================================================== I saw the model from xoid but the zipper I needed…
Remix of a remix of a remix, I really wanted the replacement to be as similar as possible to the original part, so I added a Beyerdynamic logo and L/R indicators. IMPORTANT: Printed with a 0.25mm nozzle using Prusaslicer 2.5 with Arachne…
The Ender 3 S1 has been a great machine so far except for the loud hotend fan. I had a spare 4020 blower fan so I designed this bracket to replace the one found on the sprite extruder. Even at 100% I've found it to be quieter than stock,…
Made for the Replacement Parts contest. The core model is a functional replacement for Presta and Shrader type dust caps as round on most cars and bicycles. After printing check internally for any hanging plastic which could depress the…
Not sure about the exact model. This fits perfectly in mine. Check the dimensions. Original is available and modifiable on OnShape at…
my original clamps started to break after changing the head cushion. So tried my luck with one from printables the original was pretty good only a bit to loose and I had trouble getting the cable behind the aluminium frame. I made the…
Reinforced replacement for the shift pedal hinge for the Thrustmaster T300 racing wheel. It should be the same part for the T150. For a smooth operation print the hinge in 0.1 mm layer height. I additionally added a drop of grease. Should…
An improved top fan for the GMKTEC K6. The fanmount.stl is desiged for the noctua NF-A12x25 5V PWM fan that can be directly connected to the internal mainboard with a little modification (the wires on the connector have a different…
Recently my kids were using the original connect 4 slider piece as a sword and broke it. So it became my duty to make a new one. I made this so it would need minimal supports, (touching build plate only.)
Use M3 x 12 flat head screws. They will bite and thread into the plastic. The tolerances are tighter than the OEM part, resulting in less side to side movement, and a much stiffer snap when adjusting size.
This model will work for both left and right sides of the headset. You have to replace both the front and the back of the hinge for each side that you want to replace as it will not mate with the existing shell pieces. Also, for the back…
We have had our game of "Sorry!" since the children were young, in the 1980s. Now our grandchildren really enjoy playing the game too. But along the way we've lost some of the pawns. I thought that when I got a 3D printer I'd find designs…
This fits the base of a “ 3M Command Large Utility Hook ”. I kept breaking the originals with towels so I printed a replacement, which should be a bit stronger. I printed in both PLA and PETG, but the PETG may be a little too flexible.…
As I have a very old edition with just cubes and disks, I wanted to pimp my Agricola a little with the components from the more recent versions. I have scaled all the components to their actual sizes, fixed the cattle via meshmixer and…
Cheap keybak alternative: https://www.amazon.de/ZDNT-Automatischer-T%C3%BCrschlie%C3%9Fer-Automatisch-T%C3%BCrschliesser/dp/B0BQRGTR8B Even cheaper when buying from aliexpress: https://www.aliexpress.com/item/4001346125084.html 800gr or…
This 3D model represents a replacement protective tip designed specifically for the 4th generation TipToi pen. This tip ensures the longevity and functionality of your TipToi pen, providing a cost-effective solution for maintaining its…
// [UPDATE] July 2025 - Left Shell v2 - Thin wall fix -Minor fix to remove artifacts due to thin walls. There is still a small area around mic connection that has a thin wall, about 1 layer. This fix should allows the print to continue…
Reverse-engineered this backend filter attachment piece for my Dyson V8 vacuum. More information on my website: https://dragonmountaindesign.com/2023/10/08/dyson-v8-backend-filter-attachment-replacement-part/ Direct link to Onshape model:…
My used dishwasher was missing these. STEP included.
The Power Button of my wife's Lenovo Thinkpad T570 was broken and get's stuck in the case. So i decided to make a replacement. I printed the button from Nylon. To Repair the Button you have to do following steps. Remove the battery…
Unfortunately Fairphone 6 volume buttons are prone to breaking and are not provided by the company for own replacement. The buttons are hidden under a seal that is also prone to leaking when the button cracks, so it is impossible to get…
I printed this at .05 layer height and 100% infill with “Detect thin walls” enabled and seams aligned. Still needed a bit of sanding to get the perfect fit.
I proved the need for a push stick by taking a slice out of the one that came with the saw (see last picture). This left the original push stick with reduced contact area with the timber and a sharp point on the end. As this is a solid…
An improved Microphone Version is available here . I basically remodeled every bit except for the metal parts and the stopper plastics for the size adjustments. Also, the aux cable is now detachable, and I skipped the Microphone port as…
--- Import from Thingiverse / Reupload This was my very first design some years ago and what started my 3d-printing journey. We don't have this planer anymore but this model may still be of use to someone. I also added my original…
Attention: I keep seeing people selling these models on Esty and eBay: Digital files and actual prints. STOP THAT! I have already gone after a few of them and got them banned. I will pull these off here if this keeps happening. I put…
This is a Slide Replacement and Stock Attachment Point for the Nerf Maverick. It uses the 3 small screws as well as the N-Strike Attachment nub and spring from the stock slide of the Nerf Maverick. It features a N-Strike compatible rail…
Just remove the original damaged membrane with pliers and insert the replaced part.
Got sick of my 5lb Command hooks breaking because they are so expensive to replace. This model will clip onto an existing Command wall mount for a cheap and quick replacement. Recommended to print on its side with tree supports. It may…
We keep breaking our command strip hooks at home so I made a compatible base and then decided to change the hook shape to hold my kids' headphones. I have also included a more or less direct replacement which is a bit stronger. Updated…
A common computer mouse part that breaks is the scroll wheel axle. Initially, I tried printing a replacement out of curiosity but its actually more practical than I thought it is. The SW17 and stl files for the Microsoft 1850 mouse are…
Roomba Replacement Roller Sweeper fully customizable written using openscad tested with Roomba I4 should work fine with i3 i3+ i4 i6 i6+ i7 i7+ i8 i8+J7 J8 /Plus E5 E6 E7 I,E & J Series Settings Warnings roller_sweeper_aggression - the…
Replacement Screw for the Monster Jam Mechanix Monster Truck *EDIT* Added V2 which adds a missing fillet between the head and shaft of the screw. Also, I recommend printing the screw on its side so that the layer lines are axial with the…
please let me know if you have any issues/requests I'm more happy to help you out.
The hinge on this headset tends to be a failure point for many people who like to keep one ear open while wearing the HyperX Cloud IIs. This plastic component keeps the earcup attached to the head strap making the headphones unusable if…
I recreated the whirlpool dishwasher top rack end stop as closely to the original factory part as I could using Fusion 360. It fits as well as the original piece but there is room for some improvement. Print Settings Printer Brand:…
a replacement key for TLR-7 Sub to move it about 5mm back to better align the rear buttons with the trigger guard of some 1913 railed pistols
A thicker and stronger toolbox clasp/latch for the Stanley STST18631 stacking toolbox. The photos show my model compared to the original latch. This is a remix of a latch that has even spacing for the hinge. This model has an odd spacing…
This replaces the wood dowel that rattles around in Mossberg 500 Maverick 88 can be printed in pla or tpu honestly any material should be fine. This takes you from 5 round in the magazine down to 2 to make it legal for hunting.
Did you get a little enthusiastic with your X-Carve and forgot to check that your clamps were outside the path of your routing bit? So did we! So print yourself some of these convenient replacements in 3 different sizes to hold your…
The white one in the pics is the original one. The PRUSAMENT PETG urban grey ones are the printed ones.
This is a replacement for a cardboard plastic wrap (cling film) box, in which food plastic wraps are sold in my country, at the request of my wife, since these cardboard boxes tend to break down way before the plastic wrap gets used.…
I recommend using 0.16 layer height. Original m3 screws.
Oral B always includes a plastic ring to differentiate between the owners of different brush heads so they don't get mixed up, but the color is random and there are only 4 color choices. This means you might have the same shade twice,…
This is a button replacement for the back paddles on the XBOX Elite series 2 Controller , it could be used for customization but it’s main use is for replacing buttons lost during disassembling the controller or buttons that are heavily…
This is the WD My Cloud EX2 Ultra fan cover replacement modified for 80mm fan. 70mm version and additional details are avaible here: https://www.printables.com/pl/model/107553-wd-mycloud-ex2-ultra-fan-cover-replacement-noise-r…
Easy 5 minute print!
3D-printable replacement blades for the extruder cooling fan. The cooling fan placed in front of the extruder's heat sink has the important job to keep things cool above the hot end. By accident and a bit of bad luck the fan blades can…
Wheel is a replacement for my BQQ, the original split in half. Its for use with a 11mm shaft. The wheel is 171mm in diameter. The Wheel has been printed in ASA, which i´m pretty sure is overkill. Just make sure that you have 8mm wall…
The fusion model is completely parametric and can be adjusted to your needs. The small parts on the sides may not be printable depending on your nozzel size and overall size. I printed the model with an raft and some support. These are…
These replacement parts replace the weak headband mounts of the Roccat ELO headset. If printed with the settings described below, it is more sturdy and durable than the original. Printing For the best result, I recommend to print the…
My current frames broke, so i designed this. The earpieces do fold over like normal glasses. Print the front part (frames) of the glasses face down. Print the earpieces in the best way you can figure. I found it best to have them "lay…
Replacement for the Arms of the Belttensioner designed by Wotever. Additional parts needed: 1x M8x70 Bolt (50mm Belt) or 1x M8x100 Bolt (76mm Belt) 1x M8 Nut (to hold the M8 Bolt) 1x M8 Washer (8,4x20x1,25mm) 2x M3x10 Bolt (to hold…
A simple design similar to the original. Print in TPU for the best grip.
Green house rainwater gutter adapter/replacement for an old green house. The 2nd photo shows one original part on the left which was not totally cracked (I guess because not always in full sun) The old ABS(?) part was eroded over the…
I designed these of lids for for a set of Pyrex bowls whose lids had cracked, but they are easily scalable for any round bowl or container. When printed in PETG, the beveled flutes on the edge have enough give to snap over the rim of your…
I printed this with a 0.4mm nozzle at 0.2mm layer heights and on a 45* angle as an attempt to maximize the layer cross section for strength. Be advised that you will still need supports if you opt to print it vertically. The materials I…
Did you break a part for your beautiful wall scroll? Are you missing a part out of the box like I was? Fret not, for these might help you (or they might not). This is a replacement end cap and hook for wall scrolls. I don't know how…
my mount for my stock probe broke so i downloaded the file provided by sovol and made it more optimised to 3d print instead of injection mold. by making parts that would have been hollow into solid objects. i printed it in petg to reduce…
A quick replica made to replace number block signs if your kids break them. Printed in simple PLA. Do note that if you want this to be more resistant you might want to give it a try with PETG at a higher % infill. Feel free to experiment…
