1 / 8
Handle for a Light-Up Neon Letter B Sign (Prusa Mini, No Supports) — image 1
1 / 8

Handle for a Light-Up Neon Letter B Sign (Prusa Mini, No Supports)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Two-piece printed handle for a light-up neon letter B. Holds the battery pack and USB plug. No supports.

Rating
0 / 5
Likes
0
Downloads
0
Makes
0
Views
7
Reviews
0

Updated at source:

Model information

Category
Other Sports
License
Creative Commons — Attribution — Noncommercial — Share Alike

I built this so our band family could hold a light-up neon "B" up in the stands at games and competitions. The only thing that touches the letter is its built-in keyhole hanging tab, so you don't need screws, glue or tape on the letter itself.

What it does:

  • The letter's hanging tab drops into a tapered slot. A printed pin goes through the keyhole and is locked with a snap-on C-clip.

  • The 3xAA battery pack sits in a cradle behind the handle, held by friction lips and small ribs that grip the pack. The switch stays reachable at the top.

  • The USB plug on the pack's lead pushes up into a socket on the side of the cradle, so it doesn't dangle.

  • Extra LED cable is bundled into a tunnel through the handle body.

  • The grip has a 12 degree rake and an ergonomic profile: 130 mm long, with a palm swell and a flared pommel.

  • Assembled length is about 214 mm.

Status: fully printed and assembled, but not yet tested at a full game (weight, swing, battery life).

Fit

This is made for this letter: https://www.amazon.com/dp/B0GJRQ2126 (about 225 mm tall and 19 mm thick). Its keyhole tab is 2.2 mm thick, tapers from 18.8 to 15 mm, and has a 7.6 mm round hole. Its pack is 76.9 x 51.9 x 18.8 mm. If yours is different, open handle.scad (OpenSCAD) and change the parameters at the top. Every dimension and clearance is a named parameter, and there are three quick test parts (slot, cradle, USB) for checking the fit first.

Parts to print

  • upper.stl x1: as exported (upright)

  • grip.stl x1: standing on the pommel

  • pin_tab.stl x1 and pin_joint.stl x1: on their flat side

  • clip.stl x2 (one per pin): flat

  • Or print kit_card.stl x1 instead of the pins and clips: all 4 on one card. Snap them off and trim the nubs.

  • Optional fit checks: test.stl (slot and pin), cradle_test.stl (battery pack), usb_test.stl (USB plug)

Print settings (PLA, Prusa Mini)

  • Needs 180 mm of build height: the grip prints 173 mm tall. Any printer that size works.

  • 0.2 mm layers, 4 perimeters, 5 top / 4 bottom layers, 20-30% gyroid infill.

  • No supports. All overhangs are 45 degrees or teardrop-shaped.

  • Use a brim on the grip, because it's tall and narrow. Set the seam to Rear so it stays out of your palm.

  • Dry your filament. Expect some stringing in the battery cradle.

Assembly

  1. Slide the square peg on top of the grip into the socket in the upper, push pin_joint through, and clip it. The clip tab faces up.

  2. Slide the battery pack in from the top, switch end up. Its bottom cable goes on the right side (as you stand behind the letter): down through the corner slot in the floor, out the back, and up the outside of that wall. Pinch the USB plug's edges and push it up into the socket.

  3. Coil the extra LED cable into the tunnel. A twist tie or a bit of tape on the loose lead helps.

  4. Drop the letter's tab into the slot, push pin_tab through, and clip it on the back.

  5. To remove the pack, push it up through the thumb slot in the cradle floor.

Notes

  • PLA softens at around 55-60 C, so don't leave it in a hot car.

  • If a clip cracks when you snap it on, lower clip_squeeze in the .scad file (0.6 to 0.4).

Tags