Snap-Fit Case for Raspberry Pi 5 with Pimoroni NVMe Base and Active Cooler
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Snap-on lid without screws, vents above the Active Cooler. For Raspberry Pi 5 with Pimoroni NVMe Base. PLA, no supports.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 1
- Makes
- 0
- Views
- 15
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Computers
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Made for exactly this stack. Please check before you print:
- Raspberry Pi 5
- Pimoroni NVMe Base (the single-slot base that sits underneath the Pi, PIM699) with an M.2 NVMe SSD up to 2280
- Official Raspberry Pi Active Cooler
The case was designed and tested only for this combination. Other bases, HATs, coolers and Raspberry Pi models were not tested.
Features
- Snap-on lid, no screws: four snap tongues on the long sides click into shallow pockets in the outer wall. To close, press the lid straight down until all four click. To open, push the two tongues on one long side slightly outwards and lift.
- Vent slots: 14 slots (2 x 40 mm) in the lid above the Active Cooler fan, 13 slots in the floor and 10 slots on each long side.
- Openings for USB-C power, both micro-HDMI, Ethernet, all four USB-A ports (open to the top, the lid closes over them) and the microSD slot. The GPIO header is covered.
- The rear right corner has no guide tab, so a wide USB stick next to the Ethernet port is not blocked (see photos).
- 4 mm of room on the left side for the PCIe ribbon cable.
- Clearance below the NVMe Base: 8 mm. Check your SSD and any SSD heatsink against this before printing.
- The floor has four counterbored holes for M2.5 screws into the standoffs. Optional; M2.5 x 8 mm leaves about 3 mm of thread in the standoff by calculation, not tested yet.
- Outside size when closed: 100.7 x 65.45 x 40.2 mm. Walls 2.2 mm, floor 2.0 mm, lid 2.0 mm.
Printing
- Printed and in use: Bambu Lab X1 Carbon, 0.4 mm nozzle, 0.20 mm layer height, matte white PLA, textured PEI plate, 15 % grid infill, 2 walls, no supports. Both parts on one plate: 1 h 26 min, 53 g.
- Print the bottom standing on its floor and the lid upside down (top surface on the bed). The lid STL is already in this orientation.
- The 3MF file is the project of exactly this print, both parts on one plate with the profile above.
- The snap fit was tested in PLA on this printer. With other printers or materials it may come out tighter or looser. PETG should work as well, but has not been printed yet.
Assembly
1. Assemble Pi 5, Active Cooler and NVMe Base with SSD as Pimoroni describes it (7 mm standoffs).
2. Lower the stack straight down into the bottom part, with USB-C and HDMI facing the long side with the large openings.
3. Put the lid on and press until all four tongues click.
Files
- Pi5_NVMe_Base_Case_Bottom.stl and .step
- Pi5_NVMe_Base_Case_Lid.stl (print orientation) and .step
- Pi5_NVMe_Base_Case_X1C_PLA.3mf (3MF project, both parts on one plate)
- Pi5_NVMe_Base_Case_Drawing.pdf (dimensioned sections of both parts)
About the pictures: the photos show the printed case in use. The animation and the renders are made from the CAD files and the published 3D models of the Raspberry Pi 5 and the NVMe Base; the Active Cooler and the SSD are simplified.
Raspberry Pi is a trademark of Raspberry Pi Ltd. Pimoroni is a trademark of Pimoroni Ltd. This design is not affiliated with either company.
License: CC BY-NC-SA 4.0 (https://creativecommons.org/licenses/by-nc-sa/4.0/). Free to print, share and remix for non-commercial use, with attribution. Mark your changes and share remixes under the same license.
Deutsch (Kurzfassung)
Gehäuse für genau diese Kombination: Raspberry Pi 5 auf der Pimoroni NVMe Base (PIM699) mit M.2-SSD und dem offiziellen Raspberry Pi Active Cooler. Andere Bases, HATs, Kühler und Modelle sind nicht getestet.
Der Deckel kommt ohne Schrauben aus und rastet mit vier Zungen ein. Lüftungsschlitze im Deckel über dem Lüfter, im Boden und an beiden Längsseiten. Öffnungen für USB-C, beide micro-HDMI, Ethernet, alle vier USB-A und den microSD-Schacht. Unter der Base sind 8 mm frei, bitte SSD und einen etwaigen SSD-Kühler vorher prüfen.
Gedruckt auf einem Bambu Lab X1 Carbon in mattem weißem PLA, ohne Stützen, beide Teile auf einer Platte in 1 h 26 min mit 53 g. Das Unterteil steht auf dem Boden, der Deckel wird kopfüber gedruckt (die STL ist schon so gedreht).
Lizenz CC BY-NC-SA 4.0 (https://creativecommons.org/licenses/by-nc-sa/4.0/).