1 / 3
Magnetic Wall Mount for Guition JC8012P4A1C 10.1" ESP32-P4 Panel (parametric) — image 1
1 / 3

Magnetic Wall Mount for Guition JC8012P4A1C 10.1" ESP32-P4 Panel (parametric)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Magnetic mount for the Guition 10.1" ESP32-P4 panel. 4 pot magnets, cable tunnel, no supports, parametric OpenSCAD.

Rating
0 / 5
Likes
0
Downloads
5
Makes
0
Views
64
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution — Noncommercial

🇩🇪 Deutsch

Magnethalterung für das Guition JC8012P4A1C 10,1"-ESP32-P4-Panel. Sie wird auf die M2,5-Gewindebolzen des Panels geschraubt und hält es mit vier Topfmagneten hochkant oder quer an jeder Stahlfläche.

Zwei Versionen:

  • Zweiteilige Kappen (empfohlen): eine obere und eine untere Kappe. Die untere Kappe hat einen Kabelkanal und eine Halterung für einen Kabelbinder.

  • Einteiliger Rahmen: ein einzelner, steifer Rahmen.

Hardware (zweiteilige Version):

  • 4× Topfmagnet Ø22 × 6 mm mit M4-Gewindebuchse

  • 4× Zylinderschraube M4 × 8 (greift 3 mm in den Magneten; falls deine Magnete eine andere Gewindetiefe haben, passe m4_floor und m4_screw_len im Customizer an)

  • 4× Schraube M2,5 × 8

  • 1× Kabelbinder, 4,8 mm breit

Druck:

Wandseite nach unten, ohne Stützstrukturen, PETG oder ASA, 0,2 mm Schichthöhe.

Montage:

  1. Magnete mit den M4-Schrauben festschrauben. Handfest reicht.

  2. Kappen mit den M2,5-Schrauben am Panel befestigen.

  3. Kabel mit dem Kabelbinder fixieren und das Panel an die Wand setzen.

Die .scad-Dateien sind enthalten, sodass du Toleranzen, Magnetgröße und Kabelgröße im OpenSCAD-Customizer anpassen kannst.


🇬🇧 English

A magnetic mount for the Guition JC8012P4A1C 10.1" ESP32-P4 panel. It screws onto the panel’s M2.5 posts and holds it in portrait or landscape on any steel surface with four pot magnets.

Two versions:

  • Two-part caps (recommended): a top and a bottom cap. The bottom cap has a cable tunnel and a zip-tie anchor.

  • One-piece frame: a single rigid frame.

Hardware (two-part version):

  • 4× pot magnet Ø22 × 6 mm with M4 thread

  • 4× M4 × 8 cap screw (goes 3 mm into the magnet; if your magnets have a different thread depth, set m4_floor and m4_screw_len in the Customizer)

  • 4× M2.5 × 8 screw

  • 1× zip tie, 4.8 mm wide

Printing:

Wall side down, no supports, PETG or ASA, 0.2 mm layers.

Assembly:

  1. Screw the magnets in with the M4 screws. Hand-tight is enough.

  2. Screw the caps onto the panel with the M2.5 screws.

  3. Zip-tie the cable and put the panel on the wall.

The .scad files are included, so you can adjust the tolerances, magnet size and cable size in the OpenSCAD Customizer.

Tags