1 / 9
DIY Easy Akash Kandil Base - Snap-Together Diwali Lantern — image 1
1 / 9

DIY Easy Akash Kandil Base - Snap-Together Diwali Lantern

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

2-part Akash Kandil lantern: 4 diamonds + 1 base. Snaps together, prints flat, no supports or glue. Parametric

Rating
0 / 5
Likes
0
Downloads
1
Makes
0
Views
8
Reviews
0

Updated at source:

Model information

Category
Home Decor
License
Creative Commons — Attribution

Akash Kandil: 2-Part Flat-Print Diwali Lantern

A traditional Akash Kandil frame that prints flat, assembles in minutes and needs no magnets, no glue and no supports. Post print, it takes just 1 minute to assemble with ready to snap connections.

Angle connectors

Base connector

Print 2 parts: the diamond × 4 and the base × 1.

Also known as: Aakash Kandil · Kandil · Kandeel · Akashdeep · Akash Pradip · Akasha Deepam · Goodu Deepa · Akash Batti · आकश कदल · आकशदप · আকশ পরদপ Similar to the Sri Lankan Vesak Kudu and the Filipino Parol.

Highlights

  • Only 2 unique parts: 4 identical diamonds and 1 base. There are no labels to match and no assembly order to follow.

  • Interlocking waist joints: each diamond tip has fins (3 on one side, 2 on the other) that interlace with its neighbour's and hold the corner at 90°. One short pin per corner locks it.

  • Drop-in base: the flat X lowers through the open top and sits in 4 sockets, held by gravity. Lift it out any time to reach the light.

  • Ready for paper: the outer faces are flush. The collars are made by wrapping paper around the 4 sticks at the top and bottom.

  • Hangs from 4 loops at the top.

  • No supports: every part prints flat, outer face down.

  • Parametric: open the .scad in OpenSCAD to change the size, proportions, collar height, joint fit and more.

Sizes

Face width

Assembled (width × height)

One diamond prints at

Bed

150 mm

~21 × 18.5 cm

150 × 185 mm

220 × 220

200 mm

~28 × 21 cm

200 × 213 mm

220 × 220 (placed diagonally)

Tip: Good looking Kandil's are pure 1-1 squares, rather a 0.8 ratio parallelograms. Thats a parameter in scad below and hence you can modify it. Do share, if you are able to find a better ratio for better looking lantern.

What you need

Item

Qty

diamond.stl

4

base.stl

1

Pins, about 2.5 mm × 15 mm (toothpick or cut rod)

4

Rest items are paper and glue and other stuff you would use to decorate the lantern.

Tip: print joint_test.stl first. It's just two waist tips, so in a few minutes you can check that the fins slide together and the pin goes through. If the joint is tight, increase clearance in the .scad.

Assembly

  1. Join the diamonds. Bring two diamonds together at 90° so their tip fins interlace, then push a pin down through the fin stack. Repeat for all 4 waist corners.

  2. Drop in the base. Hold the X flat, tongues down, and lower it through the open top. Each tongue drops into the socket at a diamond's bottom tip. Tilt it slightly if it's a tight fit.

  3. Add the light. Place the LED tealight on the rings in the middle of the base.

  4. Cover it. Glue paper onto the outer faces of the frames, one face at a time. Wrap a strip around the 4 top sticks and another around the 4 bottom sticks to make the collars.

  5. Hang it. Run wire or cord through all 4 top loops. Don't hang it from a single loop.

Customising

Open kandil_kit_v7_parameteric_stl_generation.scad in OpenSCAD and use Window → Customizer:

  1. face_width: overall size

  2. diamond_aspect: diamond height relative to its width

  3. top_stick / bottom_stick: collar heights

  4. clearance, pin_hole, socket_clearance: joint fit ; 

  5. Use scad to design and see how its looks if you are tweaking.

  1. Once done change the Part to these below to export one at a time 

    1. part: diamond, base, joint_test or assembly (preview)

Press F6 to render, then use File → Export → STL.

Safety

  • LED tealight only. Never use a candle or open flame. The frame is plastic and the cover is paper.

  • Hang it where it can't be knocked down or reached by small children.

Happy Diwali! 🪔 Special thanks to little bro Ankit to help drive this across multiple iterations. ❤

Tags