1 / 8
Picture Frame 13×18 (5×7 in) – No Supports, Snap-In Holders, Drillhole Markers, Stands — image 1
1 / 8

Picture Frame 13×18 (5×7 in) – No Supports, Snap-In Holders, Drillhole Markers, Stands

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Snap-together picture frame for 13 × 18 cm (5 × 7 in) photos. Mitered rails, snap wedges and snap-in picture holders

Rating
0 / 5
Likes
7
Downloads
8
Makes
0
Views
40
Reviews
0

Updated at source:

Model information

License
Standard Digital File License

A clean, modern picture frame for 13 × 18 cm photos – it also fits 5 × 7 in prints.

The frame is made of four rails with mitered corners. Small snap wedges press in from the back and pull each corner tight – no glue, no screws, no supports. Snap-in picture holders keep photo, glass and backing in place, and you pull them out again to change the picture.

What you get

  • 4 frame rails with mitered corners

  • 4 corner snap wedges that pull the miters closed

  • Snap-in picture holders for photo, glass and backing

A Test corner is available under makeables.app/generators/picture-frame

Specs

  • Photo size: 13 × 18 cm (also fits 5 × 7 in)

  • Profile: 18 mm wide, 18 mm deep

  • Rabbet: holds a 3 mm stack of photo, glass or acrylic and backing

  • Portrait or landscape: just turn the frame

  • Glass, backing and hanger are not included.

How to print

  • Orientation: Keep the orientation from the file. The rails lie on their outer edge with the front standing upright, so the visible face is printed as a smooth outer wall – no overhangs, no support marks.

  • Layer height: I print my frames at 0.12 mm for a really clean finish. 0.2 mm works fine too, the layer lines are just a bit more visible.

  • Same outer wall speed on every layer – this matters most! The front of the frame is one tall outer wall. If the slicer prints that wall faster or slower on some layers, you get ridges on the outside or bands with a different gloss, and on a frame you see that immediately. Typical causes are a slowdown for overhangs, a minimum layer time that slows down short layers, or a separate speed for small perimeters. Before printing, color the slicer preview by speed: the outer wall should show one even color from bottom to top.

  • Walls and infill: 3 walls, 15 % infill.

  • Material: Rails in any PLA you like – matte, silk or wood. Print the snap wedges and picture holders in a tough filament such as Basic PLA or PETG, because they flex when you press them in.

  • Wedges and holders: Print them flat, as in the file.

  • Test corner first: It only takes a few minutes and tells you whether wedge and miter fit on your printer before the full frame prints.

Seamless corners

Every printer prints slightly differently. If a corner shows a gap, you don't need to sand – generate the frame again on makeables.app with an adjusted miter angle (44–46°):

  • Outer tip gapes → increase Miter top view

  • Gap at the visible front → increase Miter depth

  • Wedge too tight or too loose → change Fit

Assembly

  1. Lay two rails face down, push the miter together and press a corner wedge in from the back until it clicks. Repeat for all four corners.

  2. Lay the frame face down and insert glass or acrylic, photo and backing.

  3. Push each picture holder in diagonally from the back until it clicks. To change the picture, pull it out the same way.

Your size

Need 8 × 10 in, A4, a square print or something odd like 24 × 36 cm? This frame comes from the picture frame generator on Makeables. Enter any photo size, choose the profile, add a mat – larger frames are split into rails that fit your plate automatically.

→ makeables.app/generators/picture-frame

Questions and makes

If you print it, I'd love to see a make! Questions or trouble with the fit? Leave a comment – I read all of them.

Tags