1 / 4
The2187Lite - A Handwired 65% revision of The2187 TKL with OLED and RGB! — image 1
1 / 4

The2187Lite - A Handwired 65% revision of The2187 TKL with OLED and RGB!

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

The2187Lite - A Handwired 65% revision of The2187 TKL with OLED and RGB!

Rating
0 / 5
Likes
3
Downloads
19
Makes
0
Views
492
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

Is shrinkflation amusing yet? Less 2187 for more...something

Since I recreated The1987, it followed suit that i should include this one as well. Its the more modern design with a small sprinkle of cyberpunk. The2187 is the pretend future redesign of The1987, assuming some industrious designer in the future looked back and wanted to capitalize on the popularity of the original.

The instructions and parts lists for The1987Lite all apply to this case (except the screws and knurled inserts); including the wiring and firmware (no Proton-C though, i was finally out of them)

The name, again, was originally a play on the TKL (87 keys) and some future time ...assuming some industrious designer in the future looked back and wanted to capitalize on the popularity of the original(s). Shamelessly playing on the popularity of a thing while is strictly the name of the game!

I like to chat, so comments!

Parts list:

 

Printer brand:Anycubic Large Size Chiron

Rafts: No

Supports: Yes

Resolution: 0.2mm should be fine

Infill: i used 15%

Filament brand: Hatchbox Black PLA and Clear for the first 4mm (I used Sunulu Clear PLA)

 

Notes:

Print the Bottom plate to about 4mm in clear and switch to your filament from clear to a the Grey or a color like i did.

 

Post-Printing

 

The Column to Row wiring diagram is reversed, so it appears just as it would when you have the back of the key plate facing you during soldering.

Then the Column and Row numbering in that image correspond to the pin assignments in the Elite-C and Elite-Pi pin-outs
RGB and OLED

For the OLED, i had to bend the pins slightly to add some clearance inside the case, YMMV
The OLED Displays Layer Info,, Lock Keys (CAP , SCR, and NUM) and the RGB Mode, Color Saturation and Color Value numbers

For the RGB Buttons, i glued the mount discs and then wired and hot-glued the buttons into place. The firmware provides for 18 (you can use fewer if you choose, but some animations may have a gap). I paced 8 across the front edge, 3 on each side, and 4 across the back.
Key Map

The Key Map is essentially the same as TheAlternate and match the keycaps in the photos - these are the function keys:

Fn+Q = resets the keyboard (no bootloader)
Fn+R = Resets to bootloader for flashing
Fn+the number row = F1 through F12 (Minus and Equals are F11 and F12)
Fn+P = Print Screen
Fn+[ = Scroll Lock
Fn+] = Pause
Fn+Del = Mute
Fn+Home = End
Fn+Right Arrow = Insert
Fn+PgUp = Volume Up
Fn+PgDn = Volume Down
Fn+Caps Lock = Cycles RGB Modes Forward (Adding Shift Reverses)
Fn+A = Cycles RGB Hue Increase (Adding Shift Decreases) - this only applies to some modes
Fn+S = Cycles RGB Saturation Increase (Adding Shift Decreases)
Fn+D = Cycles RGB Value Increase (Adding Shift Decreases)
FN+F = Toggles RGB On and Off

 

Tags