Tronxy X5SA Pro Afterburner Direct Drive

this is an afterburner direct drive mod for the "tronxy x5sa pro"

In Y axis you lost 10mm print space

step file is now available as I no longer have tronxy

---

V3 is now online in V3 you can use the origin tool Holders:

Thanks to https://www.thingiverse.com/qaq_rc/ for the idea with the Threaded Insert

for V3 you need to print Baseplatte_original_toolholder_V2.stl

and a origin toolholder from here (https://github.com/VoronDesign/Voron-2/tree/V2.4/STLs/VORON2.4/Gantry/X_Axis/X%20Carriage/Printheads)

You dont need to print the toolholders from this desing

In addition, 2x M5 washers and the

2x M5x6x7 Threaded Insert (https://aliexpress.com/item/4000955825877.html)

required

V2 also remains online because there is already a remix and the users should be able to access it.

---

V2 is now online with a fixed baseplate and the possibility to change the pressure head like the original Afterburner:

The assembly of the complete construction is even easier.

needed for V2 is:

Baseplate.stl

and one hotend holder (V6, Dragon, Mosquito)

M3x16 2x

M3x10 2x

the rest is the same as for V1 (only the base falls away from V1 and 2x M3x25)

---

Mounting the printhead like the original voron 2.4

these things are needed for the afterburner:

Cap screws

M3x6 2x

M3x8 3x

M3x12 2x

M3x16 2x

M3x25 4x

M3x30 4x

M3x40 2x

hex nut M3 4x

Threaded Insert M3xD5xL4

(https://de.aliexpress.com/item/4000232858343.html)

40x40x20 Centrifugal Blower Fan - Ball Bearing (24V)

(https://de.aliexpress.com/item/4001245087911.html)

40x40x10 Axial Fan- Ball Bearing (24V)

(https://de.aliexpress.com/item/32726640438.html)

a pancake stepper, i have one with a 23mm body (17HS4023), but a 20mm is better because otherwise it is very tight.

Attention: The shaft length must not exceed 20 mm, but if it does, the shaft must be shortened.

(https://www.omc-stepperonline.com/nema-17-stepper-motor/nema-17-bipolar-1-8deg-16ncm-22-6oz-in-1a-3-7v-42x42x20mm-4-wires.html)

a Bmg drive set or a Bmg extruder to slaughter

for the original sensor you need

M3x20 2x

for the bltouch you need

M3x12 2x

M3x8 2x

hex nut M3 2x

4x M2.5x8 screws are still installed on the dragon hotend holder, but they were supplied with my hotend.

The dragon hotend can also be used in the e3dv6 mount with the adapter.

For the dragon hoten you need a bowden piece of 26mm

I can't say for the e3dv6 if anyone knows, please let me know

Assembly of the adapter:

1. remove everything from the tronxy up to the bearing slide and insert the press-in nuts in the new parts + 2x m3 hexnuts.
2. screw the new base, hotend, bowden tube and the new fanduct (M3x25 2x + M3x40 2x).
3. connect the X end stop from the original hotend to the new hotend (M3x6 2x).
4. attach the new holder to the tronxy with the original screws.
5. fit the main body with the bmg inner workings, removing the bearing that points towards the stepper.
6. Mount the main body (M3x25 on the right side).
7. mount the removed bearing from the rear (where the stepper sits).
8. fit the stepper with the sprocket and insert it into the holder. then insert the M3x8 screw to fix it in place.
9. Mount latch, latch shuttel and guidler (Bmg Screw, M3x25 1x + M3x30 2x).
10. remove the fornt cover from the 40x40x20 fan and place it in the holder.
11. connect blower housing front and front cover with a 1,75mm filament piece and insert the 40x40x10 fan.
12. Mount the blower housing front and blower housing back (M3x16 2x).
13. Screw the blower housing to the bracket (M3x30 2x + M3x12 2x).
14. Mount the chain (M3x8 2x + Hexnuts M3 2x)
15. addjust you printer Like X Y Endstop position and X-max Y-max)

you can also look at the original manual of the voron 2.4 but it is a little different

Offset from the probes

Original:

X-42 Y+5

Bltouch

X-41,5 Y-6.

if you have found a mistake let me know

Do you like my work? then Support me

https://www.paypal.me/raabi1991/

This is a remix from https://www.thingiverse.com/thing:4688200

and from https://www.thingiverse.com/thing:4603647

Print Settings

Printer:

Tronxy x5sa pro

Rafts:

No

Supports:

No

Resolution:

0.2

Infill:

40%

Filament: ESUN ABS+

Withe/black

Notes:

the print settings are the same as for voron 2.4

INFILL TYPE

Grid, Gyroid, Honeycomb, Triangle or Cubic

WALL COUNT

Recommended: 4

SOLID TOP/BOTTOM LAYERS

Recommended: 5

SUPPORTS REQUIRED

None at all.

Category: 3D Printer Extruders