1 / 30
8" Newtonian Telescope "Leavitt" LITE (Metric) — image 1
1 / 30

8" Newtonian Telescope "Leavitt" LITE (Metric)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Based on Novel Tinker's 8" Leavitt keeping roughly the same design, but with the aim to be extremely lightweight (~8lbs)

Rating
5 / 5
Likes
111
Downloads
388
Makes
4
Views
4,311
Reviews
2

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

The Leavitt LITE takes the original Leavitt by Novel Tinker and does a few different notable things :

  • Use metric M4 screws & 12mm rods, this falls inline with a transition from the Hadley to Leavitt if you're coming from the official Hadley Metric Remix
  • Uses a 62.5mm secondary mirror (recommended for best uniform illumination on an F5 200mm mirror, can also cross reference with secondary mirror calculator
  • Uses an overall smaller outer radius on parts (109mm) and thinner (but still sturdy) walls & rod interfaces to cut down on weight. It isn't much but it adds up!
  • No conversion for Dobsonian mount, instead a mount interface for a Vixen Dovetail is provided with M5 screw holes
  • Slight modifications to spider + sights to fit new layout
  • Focuser clamp knob in case you don't want to buy thumb screws
  • Primary cell changed to 120mm radius inner circle, 6 raised points of contact with small holes for better adhesion
    • Inner circle widening meant to both distribute the weight more and allow heatsinks to be attached to the back. My plan is to attach four 40mmx40mm heatsinks and have a quick-attach 120mm fan actively cool (WIP)

 

All that said, much of the credit and design goes to Novel Tinker for coming up with something that would fit on most print beds. Additionally, the basics of assembly instructions remains the same (using metric screws though) with some minor edits for QoL improvements:

  • Use two (2) triangular turn knobs for the secondary cell main height screw and on the primary cell adjustment screws (one on either side of the LTA so once collimated you can easily turn them to lock) for a total of eight (8) knobs (see close up photos)
    • You can use a spring as well on the primary cell adjustment screws, but the mirror is soooo heavy I wouldn't count on it
  • Use a nut on underside of primary cell and on top of spider for secondary cell adjustments to lock screw (see close up photos)
    • Do the spider/secondary cell nut to lock the screw after collimation!
  • Can and probably should use a nut on the secondary cell main screw to lock in place
  • Put glue all along the top flat outer ring of the primary cell and then once mirror is placed along the rim on the underside, using finger or popsicle stick to smooth out. Last thing you want is your very expensive primary mirror falling out (see dead-on photo of back of primary mirror - all the silvery stuff is the glue)

 

Files that remain the same and should be sourced from the original Leavitt :

  • Focuser grub
  • Focuser inner
  • Focuser ring
  • 1.25 inch eyepiece adapter

 

 

##EDITS##

  • Added the blender file in which this was made. Unless you're computer is fast you may face some “issues” with it running slow, such is the nature of many many modifiers.
  • Added ribbed braced alternatives for the UTA, LTA could be done but is already fairly sturdy
  • Added a thicker spider alternative. Does cut down on light capture but is far sturdier
  • Added a little more tolerance to the secondary cell holder. Rising walls may be frail but that is okay, you should glue from the back anyways to avoid stressing the mirror during thermal acclimation

OCT 30 2023

  • Organized model files
  • Losmandy D-plate attachment for sturdy use (astrophotography). Holes are fit to match D-series Universal plate's top-and-bottom-most screws (see attached picture)
    • Note that it is done in two parts and makes the focuser come out at 0/120/240 deg to the mount (I have mine at 0 deg so the camera experiences the same tilt on either side of the meridian)
  • Uncut pieces for printing assembly as single pieces
  • Small top-piece that can be added for easy attachment of light shroud
  • Found the actual good M4 knob file, sorry anyone who printed the only okayish one

 

Overall using a mixture of the original Leavitt instructions and the above edits, the telescope is rock solid. In order to cut down on weight further I used 12mm 1000mm length carbon fiber rods. Pre-mirror installation the whole OTA including the ~300g long aluminum dovetail I have on it weighed 1660g (3.66lbs). With mirrors installed the OTA comes out to about 3855g (~8.5lbs)! This is light enough that I'm running it on a Star Adventurer GTI with accurate GoTo and tracking with a phone or camera attached (pictures of captures using these setups attached). 

The whole purpose was to prove that you could do DSO astrophotography with maximal aperture (aperture is king alongside exposure - don't listen to those who say aperture isn't important) on a system that costs ~$1k USD. Though as you add things like a cooled camera, autoguiding, sturdy attachment plates, etc. you are looking closer to $2.2k USD. Likewise to prove that you can mount a large Newtonian on something less than an EQR-6 (I've imaged both on a SWSA GTI and an HEQ5 later with my astrograph mods due to just barely passing weight limits). I will continue to post pictures taken with this setup, but a basic example of what can be done with standard stacking on a rather cheap mount is at the very end of pictures. The last three (3) pictures show what the optics are capable of when tuned for use as an astrograph on an HEQ5.

Secondary Mirror Graphs:

 

Notes:

 - Be careful tightening the secondary cell screws and screws pushing into the rods as you might flex the plastic and crack it (see last photos)

- Be patient with the collimation process

- If you want to do prime focusing you might want to pick up the alternate 1.25" eyepiece adapter to be able to push your focal point further down the focuser assembly (see Accessories down below)

- Using nuts to compress-lock screws in place is a useful alternative to nylon locknuts and can work even better at times

- For variable lengths on screws you can use the shorter length if you pad the hole with a little bit of cardboard. I did this since I don't like to have the screws press right up against the carbon fiber rods and scratch them up

 

My BOM for a very minimal setup using the QoL edits as seen in pictures i.e. two dovetail adapter pieces and  not full ring, compression locking nuts, etc:

Screw UsageLength mm (M4)Quantity
Tube segment pushing on rods8-1014
Mount sights and push on rods10-122
Mount sights, not on rods8-102
Join tube segments (slant)106
Spider to UTA, can push on rods163
Secondary cell main height50, 40 minimum*1
Secondary cell adjusters40, 32 minimum*3
Primary cell adjusters40, 32 minimum*3
Focuser clamp251
Focuser top panel mounting102
Focuser top panel grub lock162
Focuser front panel102
Focuser mounting to UTA104
TotalsScrew SizeQuantity

Assuming longer screws are used, use smaller

screws as necessary if you buy an assortment set

M4x10mm30
M4x12mm2
 M4x16mm2
 M4x25mm1
 M4x40mm6
 M4x50mm1
 M4 nuts~55+

Don't forget your mirrors (F5 / 200-203mm 1000mm focal length & 62.5 mm secondary) and 12mm rods! 

minimum* - You can get away with this shorter length but it will be difficult to have room to do adjustments

 

Accessories

Alternate 1.25" eyepiece adapter for being able to achieve prime focus and eyepiece focus as well

Secondary mirror minimal dust cover (still working on primary mirror dust cover, but not high priority as I'm using the cheap plastic cover that came with the mirror)

 

Tags