1 / 5
SKR3-SKR3EZ electronics enclosure for Prusa MK3/S/+ and Geeetech i3 — image 1
1 / 5

SKR3-SKR3EZ electronics enclosure for Prusa MK3/S/+ and Geeetech i3

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

I needed an enclosure for my new SKR3EZ. Now supports SKR3 + Prusa MK3 frame

Rating
0 / 5
Likes
5
Downloads
62
Makes
0
Views
951
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

Now compatible with the SKR3 (non EZ version) and Prusa MK3 frame. 

If you like my design and want to use it on different frame, just contact me and provide the hole spacing, I will make sure to update the design for you.

----------------------------------------------------------------------------------------------------------------

case for the Bigtreetech SKR3EZ controller board, to be mounted on the back of the frame of a Geeetech i3 aluminium. 

Hole spacing for mounting: the frame of my printer has 2 rows of M3 holes.

  • Horizontal spacing: 43mm between hole centres
  • Vertical spacing: 94mm between hole centres.

Mounting hardware required: 

  • 4x M3x15mm screws for securing the board to the case
  • 4x M3x15mm or 4x M3x20mm, for mounting the case to the frame
  • 8x 3mm washers to spread the load produced by the tensioned screws (4 of them to be put between the board and screw head, 4 between screw head and frame mounting holes)
  • 1x or 5x D3x8mm teflon spacers, 1 for one of the mounting holes for the board, the other 4 for having the case separated from the frame (I had to make room for cable managing the LCD EXP1 and EXP2 cables, like can be seen on the images)
  • 1x 40mm slim fan (like Noctua A4x10 FLX). I uploaded an updated design. Version 1 of the case cover has 2 fan grills, version 2 has only one, with an updated fan guard design, which has reduced the noise made by the turbulance of air through it (2 fans were a bit overkill for the heat generated by the board)
  • 4x (8x if you run dual fan setup) M3x20mm screws to mount the fans to the cover. current design requires 16mm long screws, I plan to add a bit of spacing to avoid having the screws poking through the exterior of the cover, or you could place a few washers there too

Printing parameters:

  • PLA (parts designed with little to no thermal retraction in mind, PETG should also work, ABS I don't know, it retracts more)
  • 0.3mm nozzle
  • 0.2mm layer height 
  • 3 Perimeters
  • 4 solid bottom layers
  • 5 solid top layers
  • 15% gyroid infill
  • bed: on mine (borosilicate glass with painter tape) I had to raise the temperature to 55°C to avoid warping. I don't have experience with other bed materials

Mounting procedure:

  1. Print the testing plate to ensure your steps/mm are set correctly (I forgot to change them at first lol). Use some M3 screws to check if the holes line up correctly with the board
  2. Print both sides of the case
  3. Clean the print from supports, check the holes for SD slot and USB cable: they might require some cleaning
  4. Prepare holes: this case does not require heat inserts for the screw holes, I made them 2.5mm in diameter so I could use an M3 tap to thread the holes precisely: I usually use the tap number 1 and thread only a few turns, so the screw can go in easily and then self tap the remaining of the hole. You can also use a 2.5mm drillbit to have a round hole, then use the screws to self tap the threads
  5. Mount the backside of the case to the frame using 4 M3x15 or M3x20mm screws, 4 D3 washers and (eventually) 4 teflon spacers. Tight the screws firmly
  6. Bend the cables (board power, hotend and heatedbed power) under the board, so they do not put extra tension on the wire terminals
  7. Insert screws (4x M3x15 with washers) through the board, place one teflon spacer on the backside of the screw right next to the X driver
  8. Lineup the SD card slot and USB port, insert the board on the case and tighten the screws
  9. Mount the fan on the cover using 4 M3x20mm screws
  10. Do cable management so that all of them come out the rectangular hole on the bottom, you might want to use a cable tie to keep them bundled together
  11. Connect case fan to the board and close the two halves of the case. They should stay together without the need of screws. Just in case it falls apart, I've put 4 holes for M3x10 screws to secure the two sides together.

 

Tags