1 / 3
Shelly box for T&E 3x slots and wago 221 connectors (1Plus, 1L, 2PM, 2.5, Dimmer2) — image 1
1 / 3

Shelly box for T&E 3x slots and wago 221 connectors (1Plus, 1L, 2PM, 2.5, Dimmer2)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Preliminary estimate for PETG

€3.61 – €4.42 net (excluding VAT)

For file: shellyplus_enc_light_rt_v2_1-slice_0.4n_0.2mm_PETG_MK4IS_3h39m.bgcode

This is an estimate for one file. You’ll confirm the exact price before ordering.

File and estimate settings

File used for this estimate

Average indicative estimate: €4.02 excluding VAT (range midpoint).

Weight reported by the author
62 g
Print time reported by the author
3.65 hr
Source material
PET
Estimate material
PETG
Estimate printer
Bambu Lab P1S - 0.4 nozzle
Estimate process
0.20mm Standard

Indicative estimate for the selected file only, based on the author’s weight and print time. File variants are not added together. The final price is calculated after file analysis.

Saved on this device.

Enclosure designed to hold a Shelly for wiring light fittings using the UK 3 wire system with wago 221 connectors.

Rating
5 / 5
Likes
86
Downloads
608
Makes
2
Views
5,418
Reviews
3

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution — Noncommercial

Part of my series of enclosures designed for Shelly smart devices and Wago 221 connectors.

Shelly box for T&E 3x slots and wago 221 connectors

This box was designed for wiring light fittings using the UK wiring model (feed/switch/load) on twin&earth wire with wago 221 connectors, but it can be used for other purposes. The box supports Shelly Plus1, 1L, 2.5, 2PM, Dimmer devices.

Electrical safety

  • Mains electricity carries danger of death. Please don't attempt to use one of these with real circuits unless you are competent and aware of health and safety procedures.
  • Use PETG or other fire resistant materials other than PLA.

Purpose and features

The enclosure is designed to connect 3 twin&earth wires to 1 shelly device using 3 wago 221 connectors. The wires will serve the functions of providing feed power, external switching and a connection to the load.

Shelly device support: Shelly Plus1, Shelly 1L, Shelly 2.5, Shelly 2PM, Shelly Dimmer2

Wire strain relief: Each flex wire entry port has slots for fitting a cable tie as strain relief for the wires.

Attachment holes: The box has counter-sunk holes to attach it to a surface.

Cooling slots: There are cooling slots all around and above/below the shelly device.

Lid fitting: The lid attaches to the box using 4x M3 screws (5-10mm max) which thread into M3 heat inserts to be installed on the box.

Printing notes

  • The lid requires supports on the bolt hole counter-bores, otherwise it will not print cleanly (in my case it didn't)

Version control

Version 2.1 - 11/03/2024

  • Updated (reduced) cable tie shelf width
  • Re-shaped lid to fit (issue in v2.0)

Version 2 was a significant redesign to include the following features:

  • M3 heat thread inserts instead of square nut slots or holes for tapping
  • Attachment bolt holes on the inside of the box rather than outside brackets
  • Cable tie pads inside the box as opposed to accessible from the outside (enables refitting ties without dismounting the box)
  • Shelly slot adjusted for compatibility with multiple models

 

Tags