LuminaSpira: The Infinite Glow Spiral LED Lamp.
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Finally, a super fancy LED lamp which isn't a pain in the butt to print and build.
- Rating
- 0 / 5
- Likes
- 33
- Downloads
- 94
- Makes
- 0
- Views
- 872
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Home Decor
- License
- Creative Commons — Attribution — Noncommercial
Introducing the LuminaSpira: The Infinite Glow Spiral LED Lamp.
This is a dazzling (yet extremely easy) lighting project that will transform any space. Powered by a D1 Mini WiFi board, WLED, and WS2812B RGB LEDs, this lamp offers virtually infinite colour effects to choose from, allowing you to create the perfect atmosphere for a Netflix and Chill session.
With a quick and easy assembly process (NO supports or glue/fasteners required!), the LuminaSpira is an accessible project for LED enthusiasts of all levels.
It takes just 2.5 hours to print on a BambuLab X1 Carbon (did I mention, no supports?!) and less than 15 minutes to solder and assemble (with zero glue or fasteners required - completely press-fit!)
Print specs:
- 0.28mm layer height = four bottom layers for strength.
- 0.4mm nozzle = four perimeters.
Steps:
- Print parts.
- Cut Neon Tube + LEDs to length, based on length of the 3D printed frame channel.
- Insert LEDs into Neon Tube.
- Insert Neon Tube into your printed lamp frame.
- Feed all wires through base cap, and USB power through hole in base.
- Install WLED on the D1 Mini (Note *1)
- Connect D1 to power and LEDs (Note *2)
- Press-fit everything together.
BOM
All in NZD, do your own conversions.
| Product | Cost | Quantity | Link |
| LEDs - WS2812B IP30 (60p/m) | $3.67 | 53x | LEDs |
| T1023 Neon Tubing | $14.04 | ~90cm | Neon |
| USB Switch / Cable | $1.80 | x1 | USB Switch |
| D1 Mini | $2.70 | x1 | D1 Mini |
| Filament (eSun White PLA+) | $2.10 | ~100g | |
| Total | $24.30 |
Important Stuff
*1 - Once WLED is installed, you must go to config → LED preferences and set:
- Maximum Current: 400mAh
- 400mAh is for use with basically any USB-port this might get plugged into, and the brightness is totally fine - you can technically go higher if this lamp will be powered by a dedicated USB power supply.
- LED outputs:
- Length: 53
Back in the main menu, I find the standard Rainbow effect to look excellent. If you want your lamp to “remember” it's last colour effect mode after being turned on/off:
- Set/save your favourite mode as a preset (#1 is fine)
- go into Config → LED preferences → scroll down to Defaults
- Apply preset 1 at boot (0 uses defaults)
*2 - LED power must come directly from USB power - you must not power the D1 Mini from it's USB port, then pass on power to the LEDs from the 5V power pin. Please see my amazing diagram below on how the wiring should look like - notice that the 5V power is powering the LEDs directly from the incoming 5V power (which just so happens to be a USB cable).
To be perfectly clear, what you don't want to do is power the D1 mini via USB, then power the LED's from the D1 Mini's 5V pin - this will kill the D1 mini if you draw too much power.

Final notes:
- When inserting the Neon Tube into the printed lamp, ensure that the LED strip ends on the left, where the lamp meets the base.
- Everything is press fit with a 0.02mm tolerance.
- Again, no supports. I hate supports, and you should, too.
- I would have made the spiral curve in more centrally - but we've hit the limit on the flexibility of the Neon Tubing.
- If you forget to connect your WLED/D1 to your home Wi-Fi in the initial setup, you can connect to it's Wi-Fi access point ("WLED-AP"). The password for the landing/login page will be "wled1234".