Qidi X-Plus 3 and X-Max 3 Anti-Vibration Feet Bushings
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This bushing helps secure the Qidi provided anti-vibration feet to the printer using screws and the original feet.
- Rating
- 4.5 / 5
- Likes
- 40
- Downloads
- 244
- Makes
- 4
- Views
- 2,265
- Reviews
- 4
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
See update history at the bottom of this description.
NOTE - These bushings are designed to keep the anti-vibration feet from falling off of the printer when moving it. For reasons explained elsewhere, they weren't designed to take a lot of abuse. That said, the also aren't delicate, but when you are moving the printer using these bushings, take care not to put too much stress on them.
Additional Note - I only have a Qidi X-Plus 3. Since Qidi sells the same anti-vibration feet for the X-Max 3, I'm making the assumption this bushing will work for that printer.
Description
The Qidi anti-vibration feet are designed to fit onto the original hard printer feet snugly. That's great if you don't move the printer, but if you do, the anti-vibration feet can fall off easily. After reaching out to Qidi, I was informed that this was the intended design. So I did what any good engineer with a 3D printer does, I "fixed" the "problem" by designing these bushings.
Because of the way Qidi designed the hard feet and the anti-vibration feet, there's not a lot of room to make something super strong before you're into designing completely new feet. I decided I just wanted something to keep the feet on and not something to survive abuse. There was just enough space to do that but because of those reasons, these bushings are pretty tight. If you're printer is dialed in, they should push right in. If they don't you may need to break out some sandpaper and/or files to get them down to size.
What You Need
- 4 of these bushings (either cap head or countersunk head version)
- 4 M4x25 cap head or countersunk screws.
- (optional) Purple/red Loctite or equivalent.
You'll need to print 4 of these bushings, one for each foot. I recommend the countersunk version since it has a better cross section and shouldn't be as fragile as the cap head version.
I tried to design this bushing to give some clearance on the bottom of the foot. It seems to work well with the Qidi X-Plus 3 but as we all know, the X-Max 3 is even heavier. It is possible that these bushings can bottom out with that printer and cause even more noise. Ironic, I know. If that happens a small rubber/TPU washer under the bushing may help but I really have no way of knowing for sure.
You may want to use some purple/red Loctite, or an equivalent light non-permanent thread locker that can be removed with hand tools. Qidi appears to have used this on the original screws installed with the feet. Because of that, you'll need to apply just a little bit of torque to break that thread locker when removing the original screws. This is easily done by hand using the long hex wrench Qidi provides with the printer. When you install the new screws, you will likely need to thread the M4 into the hole first to clear out the remains of the old thread locker. I highly suggest doing a dry fit of everything before using any new thread locker. If the new M4 screws don't go in pretty easily, verify that the original screws are actually M4. They should, but there's no guarantee that production runs and/or regions don't vary.
IMPORTANT - Don't go crazy tightening the screw down with these. Again, for reasons explained elsewhere, the tolerances are pretty tight for this. If you tighten it too much, you'll snap off the washer base of the bushing. It isn't the end of the world, but it is annoying when you have to print another bushing. You really just need these tight enough so the foot feels secure and isn't moving or spinning around. If you hear the bushing cracking, you tightened too much.
Settings
My print settings: 4 perimeters, 4 top and bottom layers, 0.20 layer height. I recommend 100% infill. For the cap head version, you might need snug supports. The countersunk version should print without supports.. I printed my bushings in PETG. Let's be honest, this thing is all walls. The weight is really born by the feet so it only needs to be strong enough to keep the screw in tight and to not break when sliding the printer around.
Updates
- October 25, 2023
- Added countersunk version STL and description.
- Updated description to recommend 100% infill.