24 models
Based off of the updated back cover with fan. Increased fan size from 20x20x6 to 25x25x7 and added more vent holes. uses M2.5x9 button head or maybe m2.5x8 flathead screw. i made mine from ASA. Will make from a higher temp material when I…
This remix of the Stable Bambu X1C plate holder by Mark (which I use many for my X1Cs) has been remixed to fit the large Qidi 330 x 330 plates comfortably. Very stable with one or more plates installed.
The stock motherboard cooling fan for the Qidi Xmax3 is quite loud and always on. The motherboard does not have any extra programmable fan headers, so I designed this replacement back cover to install a silent 120mm fan in place of the…
Printed in ABS Like Resin but will also work on a normal FDM Printer. Support is needed. I would use 3lines and like 20% infill. Also use a Material for high temps cause its in a closed case.
This is a simple enclosure to prevent stuff falling in the front case of the printer. There is a big gab and i had to get mutliple small parts and junk out of it. Now its closed so no problem anymore. The caps you can secure with a trop…
I had heard that the Xmax3 are the same size as the Plus4 and are swappable (with some changes to the plug) (reports are the q1pro hotends are the same length as the plus4) Later on I heard that it is 4mm short. So I Stewy helped me with…
Only a remix of the original extruder cage to allow the usage of a 4mm bearing with a Omron D2F-L switch. I didn't have 5mm ball bearing and was missing the predrill for the switch. Additionnaly, if you have an inductive Probe on your…
This is a mount for a Raspi camera (original version) will seat a 1"x1" board. Put a channel top and bottom for routing the cable away from the belts depending on the install orientation.
Just an addition to the available side mount tool holders to hold the wrench and hex keys.
Larger duct for qidi carbon filter
This part is a spacer located at the back of the toolhead, between extruder mount and PCB. It broke when I replaced the PCB with the new one, so I had to design this replacement. Printing it in ASA, ABS, or PC is recommended.
The original clips broke the first time I removed them. I designed these to replace them. It is recommended to print them in PETG or ASA
The original Qidi inductive probe failed on my printer and i had a Super pinda laying around from another project. Dimensions have been taken from the original Qidi mount, so no need to edit the printer.cfg as the X/Y offset is the same.…
По сути это перерисованный кронштейн с моими изменениями. Оригинальную модель не удалось экспортировать в твердое тело и я просто оцифровал эту модель и изменил ее исправив некоторые моменты. Схема подключения выглядит следующим образом:…
NOTE: BEFORE YOU ARE GOING DOWN THIS ROAD, MAKE SURE YOU KNOW WHAT YOU ARE DOING BEFORE SWAPPING STOCK BOARD. WARRANTY WILL BE VOIDED This is the mount for the Manta M8P or M5P to be used on the X Max3. BOM: 4x M3 dia4.5mm Heated inserts…
I used ASA. Supports are needed. separate the heater from the fan. use those 4 screw to attach heater box parts list Qidi chamber heater(heater and fan) 2x HEPA filter(80mmx40mmx15mm) 6x m4 threaded heatsert 6x m4 x25mm flat head cap…
Rod mounts in standard location on the rear of an XMAX3 to allow for use of a 3kg spool, without the drybox. Category: 3D Printer Accessories
Require: PC4-M10 PTFE Tube Connector
I wanted to mount a Nevermore V6 in my Xmax3. So i designed this blanking plate that does double duties. Both blanking off the exhaust fan hole and has mounts for this Nevermore V6 holder.…
Qidi has such a long filament path and the drag affects print quality sometimes. Thatswhy I decided to use a filament buffer device. I print ABS but you're good to go with PLA or other shit you have laying around. Very simple CAD model…
This model allows you to mount the QidiTech filament box directly on a Wall behind or next to your printer. This makes changing the filament more convenient because you don't have to reach behind your printer to unlock the filament box.…
I had 30mm winsinn fans on hand so I remixed the cover to use them
As mentioned this just supports mounting the noctua a12x25 120mm fan. I mounted mine on the outside from the inside using the supplied screws. I could have modeled a small hole in for the cable routing but am using a slot instead. It…
I wanted to mount a Nevermore V6 in my Xmax3. So i designed this blanking plate that does double duties. Both blanking off the exhaust fan hole and has mounts for this Nevermore V6 holder.…
