LayersFactory
Report model
1 / 8
EnderXY - Bed Wobble Begone — image 1
1 / 8

EnderXY - Bed Wobble Begone

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Supavitax

Supavitax

@Supavitax_238603

Potential fix for the bed wobble when Z is going up or down when you're not using triple-z by re-locating the rails.

Rating
5 / 5
Likes
17
Downloads
70
Makes
2
Views
734
Reviews
2

Updated at source:

Model information

Source
Printables
Category
Other Printer Parts & Upgrades
License
Creative Commons — Attribution — Noncommercial
DetailsFiles (11)Makes & comments (Makes: 2) (Comments: 6)Remixes (0)Collections (21)Related

Join the EnderXY community on Reddit:

https://www.reddit.com/r/EnderXY/

 

I've made this as I've received a few messages on here asking if there was a way to fix the bed wobble without using triple-z. This is untested as I use triple-z, but it should work and fix the issue completely.

You will need to add support for the left arm but it's only a small amount that has to be supported so it shouldn't add much extra time.

Remember to print 2040 linear rail guides before dissasembly to make the installation easier, I've included some to print (atleast 2).

 

You will lose 10mm on X as the Z motors had to be shifted, effectively moving the bed back 10mm so that the linear rail and lead screw are parallel, though this also depends on the thickness of the toolhead you are using.

Note: If you are using the printed bracket and location designed by belt3dprinterkit then you will have to flip the bracket (check pictures).

Top caps(Optional) (No pic):

  • 2x 608zz bearings
  • 4x M5x8mm (Socket or Pan head)

Motor mount (Pic 7):

  • 4x M3x15mm (Socket or Pan head)
  • 4x M3x10mm (Socket or Pan head)
  • 4x M3x13mm (Socket or Pan head)
  • 4x M3 spring nuts (Re-use stock)

Arm (Pic 4, 5, 6):

  • 8x M3x8mm (Socket or Pan head)
  • 8x M5x8mm (Re-use stock)
  • 4x M3x13 or 15mm (Socket or Pan head)

Z-endstop mount (Pic 8):

  • 1x M5x8mm (Pan head)
  • 1x M5 spring nut (Re-use stock)
  • 2x M3x6mm
  • 1x M3x18mm (Adjustment)

Dissassembly:

  1. Remove heated bed from bed carriage.
  2. Remove stock arms (P4L/P4R in the manual) and 1020 extrusions.
  3. Remove 1020 extrusions from stock arms (P4L/P4R in the manual).
  4. Remove linear rails and carriage
  5. Remove motor.
  6. Remove Z nut from lead screw.
  7. Remove lead screw from coupler.
  8. Remove coupler from motor.

As screws cross paths there is a very specific order that has to be followed for installation.

 

Linear rail and carriage installation:

  1. Use 2040 linear rail guides to align the rails.
  2. The rail should touch the lower brackets (P3L/P3R in the manual).

Motor installation:

  1. Connect mount to 2040.
  2. Connect motor to mount.
  3. Add Z rod coupler.

Arm installation:

  1. Connect arm to MGN12H (top bolts ONLY).
  2. Connect Z nut to arm.
  3. Connect arm to MGN12H (bottom bolts ONLY).
  4. Connect 1020 extrusions to arm.
  5. Connect lead screw.

Z-endstop mount:

  1. Follow the picture.

 

Remember this is untested until I get confirmation but I'm pretty sure there won't be any issues.

If you'd like to support my work you can here https://ko-fi.com/supavitax

Tags

enderbedtiltfixender3wobblecorexybelt3dprinterkitenderxyaditiva3dendercorexywobblefix