Counting matching models…
I believe this works for Tiagra, 105, Ultegra & Dura Ace - Shimano calipers that use K series brake pads It also works for Altus BR-UR300 calipers - or calipers using B series brake pads.
I made this to run a fan on low to create a slight negative pressure inside my enclosed printer. the fan is inline with the exhaust hose, which is vented out a window. My intent is to pull fumes outside when printing Nylon and ABS. For…
Parts are not oriented for printing. They are coming of my CAD file where they were “assembled”. Note: On my glove the left index and middle were still a bit tight. Scale up if you need.
Once you have an initial relief groove cut you can use the relief guide with the Makita router plunge base to add more grooves at 4" intervals. (Swap out the original sub-base for the 3D print). Change to the dovetail bit, check the bit…
I wanted a simple component to hang bags and items on a supporting rod with a couple of goals - prints on its side for strength, no support required, hangs level when loaded, doesn't hang too low from the bar, and looks uncluttered. I…
Flat sided - to print on its side for layering strength. The number on the bottom of the original pull tab - P15BH2 I included a 5mm thick test part so you can check the fit before final printing. I'm not sure if there are more than one…
The original was very good but I can only use one hand, so I needed to make it easier to open. I added gripping recesses on the top and bottom surfaces, and made a few other minor tweaks. When printing I set the Bridge Flow to 1.5 instead…
Router: Makita RT0701 or DRT50 (¼" routers) Vacuum: BOSCH GAS18V-3 (Hose Part Number: 1600A011RL) Support needed for the best prints.
250812 - Update - the v04 enclosure moves the screw bosses 4mm closer together for more room to route the cords. Support may be unnecessary, if you have good bridges, or if you don't mind pulling out a couple of filament squiggles. Use…
These are a bit ugly, but they worked for my purpose just fine so I'm uploading them in case they help someone out. You can flip them over for thin or thick material. There are two components. If you make the triangular pieces shorter or…
20 March 2026 - Version 02 is updated. The 2.5" end is now about 1.5mm larger to fit more snugly into tool exhaust vents. Tablesaw - SKIL 15 Amp 10 Inch Portable Jobsite Table Saw with Folding Stand- TS6307-00 Rigid Vacuum - Hose diameter…
To be consistent with the MatchFit M5 threads and to secure this featherboard - https://www.printables.com/model/288569-featherboards - I made a one piece miter bar that accepts M5 hex head screws. It's not as tall as a normal miter bar…
It can stay on the spool in the Bambu Lab AMS. I like that much better than clips that go on the roll edge.
Remixed For two 10mm x 2.65mm round magnets. Center fillet was not working in Rhino, so I just lofted a surface. I printed this in PLA with the suggested settings. I had to clean out the X1 side a bit. I'm not sure if it was filament from…
80mm long interior clamping surface. Two of these can be used in unison (exterior/interior) with a single Matchfit clamp on the diagonal. The bracket has interior and exterior matchfit clamp openings along the sides. easily compatible…
For use with a 3/8" socket extender and a IRWIN 1766068 T-Handle Tap Wrench (The Irwin tap accepts a 3/8" socket, Die handle or included pin) 12 M5 Threaded inserts and 12 M5 screws needed for assembly. There's not a lot of pressure on…
I have a 13mm rod that I utilize to balance regular motorcycle wheels. The hub mount BMW R1200 rear wheel has a 62mm opening. That's far too large for my basic setup. I made this part to seat into the opening of the hub, with a huge nut…
A nice Juicy print with standard 0.2mm nozzle settings. Just black PLA. Print bucket vertically. I used a little bit of support on the hanger. I'm not sure if you need it, but I use it.
I tried other spool adapters on Printables but they did not fit. I took spool measurements and built this one to fit on Bambu labs spools properly. 1. Print this file 2. Cover the Overture filament with painter's tape to secure it from…
Sewing machines have very tight spaces to access the screws for the presser foot, needle, feed dog, etc. I made this magnetic bit holder, as even the small screwdrivers provided with the machine were too large. The cylindrical shape helps…
I had a few hours before leaving on an international trip so I designed and printed this to cover the power button. The top portion protects the blade portion and the bottom area uses a friction fit to keep it on the razor. I just did a…
I didn't want to make these cages stick out any further than necessary from the fork so I made this adapter and used stainless steel hose clamps to secure the cage to the fork. I put Xpel chip guard film on the fork. I put VHB tape on the…
5 clip sized included for getting a secure fit on different thickness arms. I printed this out of PAHT-CF Carbon fiber filled Nylon. Nylon for outdoor use and CF for the non-slip texture. No Support needed. Add enough wall sections to…
I built mine of PETG-CF with 5 walls and 25% infill. (it's for an adventure motorcycle)
If you want to position a seam guide accurately to the left or right of the sewing machine needle, 5mm up to 21mm. This is helpful if you don't have a symmetrical foot and need to sew on both the left and right side. The holes will turn…
This has a 1mm gap on the side of the top section and a 3mm gap on the bottom section. Allows replacing metal g-hooks. I printed this out of PA-CF, but It would probably work fine in other materials. I did try standard nylon filament, but…
I had to extend a wire so I made this. Designed for M3 machine screws/nuts Make sure everything is unplugged and circuits are shut off when doing electrical work! Use flame resistant materials such as PC-FR or materials with high temp…
This fits: https://a.co/d/5D6Wu38 Depets Large Cat Door (Outer Size 9.9" x 9.2"), 4 Way Locking Cat Flap Door for Interior Exterior Doors, Weatherproof Pet Door The Depets door fits 1-1/4" thick doors. This extension makes it fit 2" thick…
My Morse sewing machine has two 5.5mm diameter spool holders that are about 60mm apart. I wanted a thread guide that would store easily when not in use. This has two components. You can probably just use one. I have a second smaller part…
Use these on any type of shower curtain to hold the bottom edge against an enameled metal bathtub or shower. I used cyanoacrylate glue to adhere the seam clip into the part. The magnet is press-fit in. No support needed. I used regular…
The prior owner did a terrible job with the airbox mod. I ride off road and wanted more protection from water and dirt ingress. I'm adding Frogzskin hydrophobic mesh to the airbox opening. If you can get the wires out of the way there's a…
The older high quality treadle rods were too short for a new motor so I made this extender. Two m5 threaded inserts are required. I sized threaded insert holes for PA-GF, so they may be large for other filaments.
This is not the prettiest fix, but it has been working for months. The sandals tend to rip out at the back of the inner rear portion that the webbing goes through. I had some gray Bambu Lab TPU 95A HF available so I designed and made…
Do chipmunks love to eat maple tree seeds under your engine hood, on top of your comfy non-woven fabric battery cover? Printed with PETG-CF. Secure with zip-ties through x-acto cut holes in the battery cover.
Tired of small rodents sitting on the engine, eating there, and leaving nut shells and droppings? I'm trying these to keep rodents off the engine. I'll probably make one for the flat area of the swingarm too. Two colors in the photos…
I doubt you'll use a printed pickguard so here's a step file for easy manipulation. Perimeter chamfer not included.
The CLEAN button is right above the power button. With my model it goes into a 25 minute cleaning cycle if you touch the button. There's no way to exit that cleaning cycle. If it's morning and you need that first cup of coffee this is not…
These are all currently available results.
