Counting matching models…
This is a center axle bracket that uses the existing bearing holder and axle. I added two different diameter axels to use for spools with larger or smaller center holes. Print Axels with supports as they are at a 30-degree angle to make…
Made this for the garden. it is extensible you can add multiple sections to make it higher. I printed this in polycarbonate but PetG should be just fine. I used a silicone sealant on the pipe joints and to hold the bracket between the…
A Print in place tree ornament Silk PLA .15 layer height, no supports required.
Compliant cell phone holder. I wanted a phone holder in my car that was easy to use. I can use one hand to put my phone in the holder and remove it. I used PolyCarbonate to print this so that it would take the heat in the car. should be…
Cover to keep the rain out of the grease trap bucket. on a traeger pellet grill. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .3mm Infill: 100 Filament: generic Polycarbonate Carbon fiber fill…
A temple for your weaving looms to help with your selvages. The clamp is a butterfly-style clamp that you attach a weight on a cord. See the pictures. A spring or rubber band is recommended to help close it and make it easy for one-hand…
Simple weighted warp weight for floating selvages or repairing a missing or broken warp. Fill with pennies to adjust weight add a small screw hook to the lid tie your thread on the body and wrap around for the needed length and hook the…
This is a Scupper hole plug to keep water from coming into the sit-on-top kayak from the scupper holes. These are printed in flexible filament to allow for a tight flexible fit. to assemble put the ball into the plug and glue on the grill…
A series of strap connectors with a thumb release. I used a generic polycarbonate Carbon Fiber filament. updated the latch and housing to have better strength changed the layout for the housing. improved tolerances. and added positive…
designed this as a print-in-place holder for things with a broomstick-like handle less than 25mm in diameter. Two versions are available - long and short arms. It is printed upside down you need to mount it with the v of the slots…
This is a Scupper hole plug to keep water from coming into the sit-on-top kayak from the scupper holes. These are printed in flexible filament to allow for a tight flexible fit. to assemble put the ball into the plug and glue on the grill…
This is a parametric bobbin used in shuttles for weaving. To match my shuttles, I needed more bobbins of differing lengths. no supports needed Print the pins on a raft or with brims. Superglue the halves together. I have attached my…
Hinge to attache to Plexi Glass. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Category: DIY
Print in petG, ASA, or Ploycarb preferred. PLA is too brittle for the cranks. you can get the alligator clips on Amazon Use small wood screws to attach the retainer clips Assemble the cranks into the tophat, put a washer on the crank, and…
This is an end feed shuttle with pirn. I used brass wire to make the loops and hooks for the tensioner and super glued them in the holes. Two of the hooks for the take-up and exit are formed in complete loops the rest can be simple hooks.…
Cap adapter for the steel dispenser needle to add to a bottle of superglue. Provides precise control of the amount and placement of glue. Easy clean clogs with a lighter lasts as long as the bottle of glue. printed in PETG .15 layer…
I saw this in an antique store and I thought I can do this. 3x 3mm x 45mm screws and 6 3mm nuts are needed use the two nuts on each screw to lock them in place you could use thread lock or ny-lock nuts as well. Print Settings Printer…
I had too many different spools of wire and solder on different sizes of spools. I created this to help combat that problem. Enter the demisions of the spool - outside diameter of the spool the inside diameter and the width of the spool,…
needed an easy to use repair heddle for my Harrisville 40" loom. i have several of these great for fixing threading mistakes. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 100…
‘Helping hands’ are used to hold lease sticks while dressing my floor loom from back to front. The .3mf file has two bolt sizes. Based on the thickness of your warp beam, remove the size you do not need before slicing. The bolts are 8mm…
These are all currently available results.
