All models

Customizeable Chastity Key Safe

Command Strip Shower Head Holder

I didn't have mounting hardware, but an abundance of command strips, so this can be mounted to tile with 2 command strips toward the top. Should not require support. Just beware that adhesives like command strips tend to fail eventually…

Pacifier Vape V1

MHP30 Mini Hot Plate Travel Box

I adapted the great parametric rugged box model to fit the tiny Miniware MHP30 hot plate because I was worried about its thin struts getting bent. This is small enough to throw into a little soldering kit. The parametric .f3d model is…

40mm Nato to 22mm adapter

Quick modification of ThatDrewLion's great model over on Thingiverse. Not intended for for any kind of personal protection - you could throw certain filters on it, but it's not necessarily airtight. For most applications, you'll probably…

Airpod and Apple Watch Charger Stand Remix

Remix of KacperL's airpod / apple watch charging dock. Added a hole to help eject the watch charger, and a fillet on the weighted base to match the rest of the design. Thanks for uploading the Fusion 360 file with the original, it's a lot…

140mm Desktop Fan Spacers - 12,22mm

12 and 22mm thick spacers for generic 140mm PC fans. I found that even with quiet fans, they get REALLY loud when there's sheet metal from the PC case near the intakes. Spacing them at least a centimeter away from any obstructions makes a…

Israeli gas mask lens cover

Locking plugs for IKEA Skadis drawers

Shorter version of the locking plugs for SKADIS hooks , these will keep the container lids in place, which I found were especially prone to getting bumped off the board. The removal tool is also modified to allow it to fit against the…

SlatWall (1/2") Headphone Hanger

Made to fit in the 1/2" metal slatwall built into a cubicle, this will hook in for a wall-mounted headphone holder. There are 2 versions - a solid and hollow one. Printing the hollow one may actually take more time and filament because of…

Pepper pot Israeli gas mask covers

Similar to the original lens covers, these fit in Israeli gas masks. Visibility through them is surprisingly good if you're just after that aesthetic. Holes are 1/8 inch diameter. Printed in PETG. Category: Costume

Question Mark Trophy

Very easy to print and assemble trophy. I spray painted the question mark gold to make it stand out from the base. Category: Sculptures

120mm Tinker-Friendly LACK Riser For Printer Enclosure

Taller remix of Zuspiel's Lack enclosure feet to fit my slightly larger printer inside. The design allows the top table to simply be lifted off for access to the printer. In all I spent around $30 for the whole thing - $24 for 2xLACK…

Caster Foot for Ikea HELMER Drawers

Foot to prevent the Ikea HELMER drawers from rolling around whenever you try to open them. Fits a 1/2" wide by 1" diameter caster wheel - you only really need 2 to keep the thing from rolling. Put them under the front or back casters.…

Printbed-friendly Pry Bar

This is a small pry bar for getting stubborn parts off the print bed. The hope is that the rounded fulcrum will ding my bed less than a sharp angled one would. Works best on parts with some kind of chamfer or lip at the bottom. I have a…

Really bright LACK lighting with IKEA MITTLED strips

I used to use LED strips above my printer in my LACK rack, but the shadows cast from that angle made it hard to see the very bottoms of parts, to tell if they were starting to peel up from the bed. So I made these mounts to light parts…

Wall Anchor Mount For Ikea Shark

A big hook for hanging up an IKEA shark to keep him off the ground. There are 2 versions - one with a hole at the top of the anchor, and one with the hole filled - the filled version is for hanging with command strips, which work well…

Headboard Tissue Holder for Trysil Beds

A headboard-mounted tissue holder to free up some of the space on my tiny Trysil bedside table. Fits Kleenex 230 boxes snugly (226x121x118mm), but should be easily remixable for other sizes. For ease of printing the headboard hooks and…

PAX to gasmask magnetic quick connect

Eye of the Universe Stranger Version

This is an icon from the Echoes of the Eye expansion of Outer Wilds. The Fusion 360 source file is attached, which was based on an SVG file from Reddit . I printed mine in white and glow in the dark Overture PLA to use along with some…

Headboard ...Cup Holder for Trysil Bed

Uses the same headboard dovetail hanger from my last two designs. All Fusion 360 design files (.f3d) are included. Printing: Hook should be in PETG or other strong material, PLA is strong enough for the main body. Requires no supports,…

1mL Perfume Sample Vial Stand

If you have a million sample vials laying around like I do, this is a lot nicer than digging through a plastic baggie or a drawer. Holds 22 1mL vials with a diameter of about 8mm. Printed in Red PETG at .2mm layer height. Concentric…

Captive Polarizing Filter Frame and Case

Small kit of filters to play with lasers, polarized light, photoelasticity, and diffraction gratings. The filter frame holds a captive 80x80mm bare polarizing filter, which makes it easier to handle without smudging or scratching it. The…

Headboard Paper Towel Holder for Trysil

Designed to hook over the 22mm thick Ikea Trysil headboard, but the hook .STL or source Fusion 360 file should be easy to adjust to different sizes. The hook is printed as a separate part, which joins the main body via a dovetail joint.…

20mm Nogasm Adapter