Counting matching models…
Derived from Festool vacuum MFT hood by ggragg , to vacuum while working on the bench. Use a Insta-Dog to attach to the MFT table. Has internal radial pins to connect to the 27mm CLEANTEC hose.
Replacement adapter to 36mm cleantec hose. It does not swivel, preventing the hose to get stuck on the rails. The side panel of the tracksaw needs to disassembled to install the new adapter.
The fence size is the same as Timo's, but allows cutting at -45, 45 degree angle. In addition: Added .1 mm to fit more easily Add lock mechanism with 2 M3nS nuts and 2 M3x14 bolt (from the MK3S+ Fasteners spare bag) to lock the track. The…
To store small parts, a half height 50x50mm box may be more convenient than a full height 50x25mm.
Replace the cable with a plugit adapter. The change is reversible. Needed: Festool replacement part # 489742 two #6-32 x ½'' machine screws To install: Mark which plugit adapter cable replace the black/white cable Remove the cable, strain…
Mix of 2 designs: Festool 150 RO sander holder by gronax Systainer accessory by 3dprintedworkshop
In Fusion 360, using midplane, cut and mirror, extend existing boxes for longer tools
From Moren's project, added an indent for strength. The Fusion 360 is parametric to change depth and height.
Connect the systainer SYS-Sort latch to a plate to hold systainers for a dolly or a plate on top of a compressor. The .f3d has a parameter for how deep the feet are 3 height are sunk into the plate: 0mm: the feet are on top of the plate…
Collector to gather most of the dust when using a trim router table. Connect to festool 27mm cleantec hose. Several solutions were considered, but using 4 magnets if good enough. A rockler universal rail (3/8 in thick) is too much for…
TS55 cover: Remix gcode to reduce the amount of support needed.
Copy of the RUWI support rail . Use on MFT table to support 4x8 or hold pieces down. Demo here The project 3d printed parts includes: regular connector to the MFT longer connect to slide ¾'' part under the part being manufactured cover…
Another Portable Drill Press, designed around the makita drill XPH07Z . It can be used with a vacuum pump to hold the position, even horizontally. The base can be used to drill round stock with its vee-groove. Makita small router base…
Inspired by Festool SYS3 M 112 RA Socket and Organizer Centrotec Sets (577134/576932), based on the Systainer Organiser Boxes project , put rachets and bits in the same organizer. The foam comes from a shaper orign project . The f3d…
This connector replaces the existing adapter, to connect tightly to a 27mm cleantec festool hose.
Add a festool plugit connector to a Fein MultiMaster FMM 350Q. Part needed: Festool replacement part # 489742 One extra screw similar to the one used in the MultiMaster. Instructions: Open MultiMaster Remove cover (6 screws) cable,…
Accessory to catch dust. Tested with Bosch GWS13-50VSP 5 inch angle grinder.
Equivalent to Festool part# 575667 but allowing non-Schuko plug. In particular it replaces the Festool part# 575668 with a NEMA plug that has been discontinued. Parts used: Dust proof power outlet Cord grip 4x M4 nuts 4x M4 flat head…
Inspired by the Festool CMS PS 300 module, parts to install the PS300 Jigsaw inverted and collect dust (barely) using a Festool Cleantec hose. The plate is a shaperhub project . In addition the model includes a connector to fix the plate…
Cover for the Kreg Jig 320 to collect dust with a CLEANTEC connect. Reuse the Kreg clamp adapter pad to ease positioning. To make sure the connection between the plate and the connector is solid, the in-fill is bumped to 35%. The first…
The base design started from this thread . Tanos/Festool SYS3 ORG bins or boxes from this project can be used.
Merge 2 projects into one: https://www.thingiverse.com/thing:4556541 by hemichromebeast https://www.thingiverse.com/thing:2936707 by Joe Monkey The .f3d has a parameter for the rod diameter (within reason). Printed for 7/8'' diameter rod.
Connect a tomlemeo micro table lamp to a mft3 table or any other 20mm dog hole based table.
Parts to allow securing the ShaperTools BenchPilot to a Festool MTF/3 table, or any bench with 96mm pattern of 20mm holes. After installing the frame on the MFT3, use knobs to secure it. Homemade knob comes from this parametric design .…
Follow the Replacement instructions to replace the metric depth stop. Printed in Atomic Carbon PETG PRO .
Connector between the exhaust of the Dewalt 735 Planer to the Black&Decker leaf collection system . Wood chips are neatly collected in a trash can.
Drop-in replacement for the regular 6/8 1/4in bits holder. Accommodates 14 bits, 2 large bit slot on the site if needed. Note: with this holder, the tray does not fit in the middle compartment of the lid.
Connect a power strip to a systainer securely, to emulate a Festool SYS-PowerHub ! Used a specific power strip , remove its plastic sides and replace them with these parts to securely attach it to a systainer (TLoc). I had to cut the…
Following on BenchPilot MFT holder , the model lift the workstation by 5mm above the BenchPilot; otherwise the Shaper Origin will not sit flat on the workstation when connected to BenchPilot. See thread . This print is inspired by…
Connector to attach a trim router table to the Shaper Workstation . It has an indent to hang the table on french cleats. See that project for bolt and knob needed to complete the project.
Parts to store a Fuji Mini Mite 4 (Other HPLV spary system should fit) in 2 Systainer3 M 337. tray for tall boxes, same format as Festool M89 organizer Post for the spray gun The systainer inserts are documented on shaperhub .
Adapter to use the Kreg KMS7215 Micro-Adjuster with a POWERTEC 71536 Router Table Fence: 1 ¼-20 nut needed: the print is interrupted at 10mm to insert it. Connect the adapter to the fence first, at the left handle, then screw the…
These parts are screwed in a systainer plate and the compressor frame. It allows attaching systainers above the compressor. The top upper front metal bolts are replaced for the front connectors, while 4 ¾'' countersink screws hold the…
Similar to a T-track tray , but with different holes for the accessories I use with the Shaper workstation: 19 mm Wrench 4mm Allen Wrench Vacuum Hose clips Router bits Suction brush Although the tray can stand by itself, it can be secured…
Instead of using the provided bracket to hold the Benchpilot EStop, install it on the side of table, against the aluminium profile. BOM 6 M5 nuts 4 25mm M5 Button Head Socket Cap Screws Bolts (20 mm should be fine as well) 2 15mm M5…
Simple holder for the angle grinder disk, held in the systainer by foam inserts. The inserts are cut with Shaper origin, available on Shaperhub . The festool plugit connector adaptor for the grinder is printable .
To connect a paper roll holder to geartrack. Based on an existing heavy duty holder . 4 #12 ½'' screws and bolts needed.
When working on long pieces, the 20mm frame is limiting the thickness of the pieces. With 4 feet like these, we can use the MFT table as the frame. Installation make sure the locking pins from the left and right arms are in place before…
To support a baseboard that can raise up to 60mm. The feet has 2 legs, it can raise the base board from 2m to ~40 or 30mm to ~70mm. In each leg a bolt is inserted. A 3rd bolt per feet lock the screw. The screw are special, they are…
Change the parameters in the enclosed .f3d to match our table/umbrella. Wood PLA Filament was expending on the XY plane, made the ring smaller/thinner. Since it is not structural, outdoor exposure is not a concern. Beside it is a…
Another holder for track saw rails. The top part fits inside the T-Loc Systainer (not sys3), connects to the rail T slot, hides behind it. The bottom part sits on top of Systainer³ SYS-RB Cart, envelops the bottom of the rail.
To connect a PICTRON Smartphone Adapter to velbon CX-640 Tripod. The adapter slide into the QR plate and is secured by a a D Shaft D-Ring 1/4" Tripod Screw . Printed with Carbon Fiber infused PETG at 80% infill for maximal strength.
The provided mounting brackets are screwed over the 3d printed parts. The parts slide into the systainer pockets and then the power plug is installed. 2 pieces are needed, one is the mirror of the other.
Larger - non-symmetrical wedge to - help - remove systainer3 handle. Need to mirror the .3mf to print one for each side of the systainer.
Replace the regular Velbon Quick Release (QR) plate (QB-5LC Quick Disconnect Plate) and Sony GM Lens Foot with a single part, and insure straightness. Printed with Carbon Fiber infused PETG at 80% infill for maximal strength. After…
2 holders for the Bessey Beyceps BEY9. They are exactly 391mm long, perfect for a systainer. An optional foam insert is available to keep the holder in place. Thanks for BS Horb for the systainer3 model
Replace to provided exhaust port with a Festool Cleantec compatible one.
Black Diamond Cosmo headlamp hinge replacement using Countersunk screws and Nuts to secure it: the existing holes were stripped.
Mashup of 2 designs: Customizable Wrench Holder Peg board screwdriver holder Allow storing wrench perpendicular to the peg boards, saving a lot of space.
Makita PJ7000 to Festool 27mm CLEANTEC hose connector. Replace existing hose connector.
Remix from https://www.thingiverse.com/thing:4861771 , added a CLEANTEC connector. Knob is from https://www.thingiverse.com/thing:3713327
Dock for holding the DF500 up, to the MFT3 table aluminium profile. Slide the dock then use 2 T-Nut from the festool@ mft accessories, 2 m5 nuts and 5x20mm bolts to hold the dock to the MFT table rail. The DF500 slides and is held tight…
Edge sanding attachment for festool ETS EC 150 sander. Clamp and Guide are connected with 2 M5 nuts and 2 M5 x 20mm Clamping Knobs
Connect 27mm Cleantec Festool Hose to Makita Router dust attachment 159995-1 . Printed in TPU to fit snuggly with the 2 ends. For ease of printing, the wall in the middle in the original design has been removed, so the festool hose must…
Rubber grommer to install in the hole for the steam know hole. Reduce wooble when tuning the knob. printed using TPU
To connect the 27mm festool cleantec hose to a wire brush, to collect concrete dust at the source. TPU is required, as the hollow broom connector get a lot of stress from the hose weight.
This part allows a shaper origin sled to glide on top of the MFT. Several versions are posted: due to precision error across the length of the sled, the pin may have to be truncated a little, by .5mm or 1mm.
Holder for WS2 multiprobe water sensor. Measure Rancilio Silvia espresso machine water tank level and report the information to home assistant via a template sensor and the ESP home integration . BOM WS2 water sensor and 3 probes 6 10mm…
Printed in TPU, replace the worn out pads.
These are all currently available results.
