Counting matching models…
After setting up my Neptune 4 Plus I thought it was a pretty big shame that there was no cable management. It just looks sloppy. Looking at marketing material there is nothing done to spruce up the look. Always thought this chain has a…
Rethink of the original “hotend_clip.stl” that is one of the 5 models in “Give your Elegoo Neptune 4 Plus/Max a spine, a cable chain spine” by edl (me). This remix provides additional support for the connection point between the hot end…
You can see the control board lights attempting to peek through the cabinet of your Elegoo Neptune 4 Plus and tell you something. Covering up that light show seems a shame so a new reimagined front panel was in order. While I'm not sure…
Second set of spine models for the Elegoo Neptune 4 Plus/Max. This is to complete your printer if you have already printed “Give your Elegoo Neptune 4 Plus/Max a spine, a cable chain spine” also by edl. Print these 3 new models and have…
Simple redo of the original “z_bracket.stl” that is one of the 5 models in “Give your Elegoo Neptune 4 Plus/Max a spine, a cable chain spine” by edl (me). This remix should help out the n4max folks as well as the n4+ as the added length…
Reworked just the Body portion of the original design as Cardboard spools (from Elegoo) needed more clearance. Those walls would grind at the cardboard and leave dust. Use the instructions and other components from "Elegoo Neptune 3/4…
This quest was to reduce the background noise in the room that is my office. When the printer is idle there is a huge amount of noise coming from the power supply fan over my music listening. If a print completes overnight everyone gets…
The longer hook makes it easy to get the band(s) attached when the bolt is in place, and the shorter hook positions at about the same place as the original. Either hook should be less frustrating. These are a direct replacement for the…
Two different brackets to create a 45 degree trellis out of cheap 2x2 wood. Designed for 39mm material to give a bit of wiggle room. The A bracket creates the 45 degree peak, and the T bracket is reversible allowing it to be the top (up…
Our family likes to hit the pools and beach during vacation. Hanging stuff outside or on the chairs is typically frowned upon. Wet stuff in your luggage stinks. This simple hanger is tight at 26mm, and snug at 22.5mm which seems to be…
Right angle bracket for three-quarter inch wood plank (full 3qtr) and the always a bit less than three-quarter plywood (thin 3qtr). Use it to hold planks of wood together while dry fitting, securing, or glueing together of lumber. The…
Have you ever set up your mobile device on the seat tray just so only to have the tray move and cause your device to fall to the floor? Do you need a compact adjustable mobile stand while you are traveling? Do you spend your flight time…
Simple pull tab replacement that sits under the screen frame versus being embedded in it. Designed around a 8mm (5/16") screen frame width. Our frames have springs on the top corners that put pressure on this replacement tab at the bottom…
Originally developed for the v3.1 Elegoo Neptune 4 / Pro Fan Shroud by OrzOrzOrz as my Noctua fan with the squishy corners did not get completely covered. Then went on to make a collection of the various 40mm sizes. Hopefully these will…
Two different pods for your 1950’s spaceships to fly between. Designed exclusively for printing in spiral/vase mode. Have scaled them up by 30% and down by 30% to vary the ornaments on the tree. This creates a bit of perspective as you…
This tray may only be applicable to a single variant of the PCB5.0 so take a look at the picture and make sure what you have is the same. The tray only comes up to the height of the PCB surface avoiding interference with the external…
If you look over on Amazon for ASD LED Disk Lights you'll find these. They are color selectable in the white range to match the aesthetics of the space and surface mount to most any existing box configuration. The included lens spread the…
You can go two ways with this: Static Band - Print the no_light_band and five of the no_light_bubble Light Up Band - Print the light_band and five of the light_bubble and five of the light_cover In all cases the parts snap in, see…
After some looking around I could not find anything that suited my needs. Putting these up so others may save some time. The Theodore model pictured is a bit shorter with landscaping pin recesses. Use your slicer, tinkercad, etc. to add…
Do you have a Cheap Yellow Display lying about? Perhaps something you purchased thinking I'll make something cool out of this someday? Well today is the day! First see Till Harbaum's work https://github.com/harbaum/galagino as there you…
These are all currently available results.
